Managed 10/100 Mbps RJ45 to Multimode ST Fiber Media Converter MMC110MMST Instruction Manual
FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Instruction Manual Table of Contents Introduction ..................................................................... 1 Installation........................................................................ 2 Connecting to Power..................................................................2 Configuration and Management..................................... 3 Web Browser Configuration......................................................3 Logging Out Of The Monitoring System.............................
Instruction Manual Introduction Thank you for purchasing a StarTech.com Managed 10/100 Mbps RJ45 to Multimode ST Fiber Media Converter. A perfect solution for large, high speed networks that require expansion of fast Ethernet networks over long distances, the MMC110MMST acts as a standalone device allowing for one-channel media conversion between 10/100 Base-TX and 100 Base-FX network segments.
Instruction Manual Installation For optimal performance and safety, ensure that the MMC110MMS is installed in an area that meets the following specifications: • A temperature between 0 to 45° Celsius (32° and 113° Fahrenheit) • Relative Humidity (RH) less than 95% (non condensing) • Surrounding electrical devices that do not exceed the electromagnetic field (RFC) standards for IEC 801 3, Level 2 (3V/M) field strength • Adequate ventilation, with the ventilation holes on each side of the equipment being
Instruction Manual Configuration and Management The MMC110MMST Media Converter can be configured and managed through SNMP, Web browsers, and Telnet, as outlined in the following sections: Web Browser Configuration Logging Into The Monitoring System The MMC110MMS is accessible through a web browser such as Internet Explorer. To access the MMC110MMS monitoring system, enter the default IP address of the MMC110MMS, 192.168.1.10, into your browser’s address bar.
Instruction Manual Main Menu The main menu of the monitoring system is persistently displayed on the left side of the screen after log-in. Options can be selected with the mouse cursor.
Instruction Manual • Device Name: A device name for the MMC110MMS can be set by the user in this field. • New Password: A new password for the monitoring system can be set in this field. Setting a new password in this field requires entering the previous password in the Old Password field. • Old Password: The password that was previously being used to log in to the monitoring system must be entered here when a new password is being applied.
Instruction Manual • DHCP: Allows the user to set DHCP to “Enable” or “Disable”. If DHCP is enabled the MMC110MMS will set its’ IP address according to a DHCP server. This IP will replace any other IP address that the Media Converter had been using. • IP Address: Allows the user to set an IP address for the MMC110MMS. The default address is 192.168.1.10. • Netmask: Allows the user to set the Netmask or subnet mask. The default is 255.255.255.0.
Instruction Manual • Media Port Status: Individual status reports for both the 10/100 TX port and 100 FX port in these categories: • Link Status • Receive Count • CRC Count • Drop Count • Collision Count NOTE: The Apply button in each sub-menu page applies changes for that page, but does not save them beyond the current session. For any changes made, the user must select “Save” from the main menu.
Instruction Manual age limit on how much bandwidth is allocated for broadcast traffic passing through the MMC110MMS. If Broadcast Storm Protection is enabled on either or both of the ports, the Broadcast Limit percentage will be applied on the data packets using that port. • Media Port 1: 10/100 TX • Port Mode: Allows the user to set the port mode to Auto, 10 Half Duplex (HD), 10 Full Duplex (FD), 100HD, or 100FD. • Flow Control: Allows the user to enable or disable Flow Control.
Instruction Manual NOTE: The Apply button in each sub-menu page applies changes for that page, but does not save them beyond the current session. For any changes made, the user must select “Save” from the main menu. MAC Address Filter The MAC Address Filter sub-menu contains fields for each of the two ports on the MMC110MMS that allows the user to enable MAC address filtering for specific addresses.
Instruction Manual to a VLAN group. Users can choose TX Port, FX Port, or Mgmt Port. If Mgmt Port is selected, one of TX Port or FX Port must also be selected. • Untag: Allows the user to enable tagged or untagged VLAN for that VLAN group. The MMC110MMS supports a maximum of one untagged VLAN. NOTE: The Apply button in each sub-menu page applies changes for that page, but does not save them beyond the current session.
Instruction Manual The default get community string for the media converter is public. • Set Community: Allows the user to set the setcommunity string. If the SNMP Network management station only knows the set community string, it can read and write to the MIBs. The default set community string for the media converter is public. NOTE: The Apply button in each sub-menu page applies changes for that page, but does not save them beyond the current session.
Instruction Manual NOTE: The Apply button in each sub-menu page applies changes for that page, but does not save them beyond the current session. For any changes made, the user must select “Save” from the main menu. Save The Save sub-menu allows the user to confirm any changes that have been made in the monitoring system. If changes are not confirmed with this function, they will not be stored in the MMC110MMS.
Instruction Manual mc-status(ms)..........Get central MC status mc-config(mc)..........Get central MC configuration netconf(nc)..........Get networking configuration sysinfo(si)..........Get system information • Set Command - Usage: set(s)
Instruction Manual Specifications Applicable Standards IEEE802.3 10Base-T IEEE802.3u 100Base-TX/100Base-FX Ports 1-port 10/100Base-TX with RJ-45 connector 1-port 100Base-FX with fiber optic connector Speed 100Base-TX: 200Mbps full duplex 100Mbps half duplex 10Base-T: 20Mbps full duplex 10Mbps half duplex Performance 148,810pps forwarding rate for 100Mbps 14,880pps forwarding rate for 10Mbps Port LED Indicators Unit: PW/FA TX: LK/AT, FD/CL FX: LK/AT Dimensions 80mm (W) x 145mm (D) x 20mm (H) (3.
Instruction Manual LED Status Indicators 2 3 1 LED 1. PW/FA State Steady (Green) Power On Off Power Off Steady (Orange) Booting or failed Steady 2. LK/AT 3.
Instruction Manual Technical Support StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. Warranty Information This product is backed by a one year warranty. In addition, StarTech.
StarTech.com has been making “hard-to-find easy” since 1985, providing high quality solutions to a diverse IT and A/V customer base that spans many channels, including government, education and industrial facilities to name just a few. We offer an unmatched selection of computer parts, cables, A/V products, KVM and Server Management solutions, serving a worldwide market through our locations in the United States, Canada, the United Kingdom and Taiwan. Visit www.startech.
