Use and Care Manual

11
I: Manual water supplying symbol; O: Automatic water supplying symbol; Arrow of this symbol ashes,
means the water is owing into the water tank. If this whole symbol keeps displaying, means no main water
supplying at present. Ice-cube symbol, when it rotate, means unit is making the ice cube; and it ashes,
means the unit is in ice harvest process.
F: Fahrenheit (ambient temperature) H: Unit of hour (setting the timer) M: unit of minute (ice-making
setting and countdown time)
1. Plug on the main power supply plug, then press “ON/OFF” button on the control panel to begin the
ice making cycle. The unit ON/OFF state symbol will keep lighting on, the left number in the LCD display
window displays the present ambient temperature, and the right number displays the present ice-making
setting, and the ice-cube symbol rotates. When the left number change to ash, then the number means
the countdown time to complete one ice making cycle.
2. Each ice making cycle will last about 11 to 20 minutes, depending on the ambient temperature and the
water temperature. And for the rst time, according to the initial water temperature, ice-making last time
will be a little longer.
3. When the ice-making process is over, then switch to ice-harvest process. During the ice-harvest process,
the ICE cube symbol change rotating to ash. At same time, the arrow on the manual lling water symbol
will start to ash, the water will ow into the water tank again till the oating ball of water level switch
rises up to the highest position, then the water stop owing and the whole manual lling water symbol will
disappear.
When the ice-harvest nish, the Ice-full detecting plate will rotate downward once, then recover to the
original position and enter to the next ice-making process.
If after the rotation of the Ice-full detecting plate, it is pressed by the ice cube and can’t recover to the
original position, means the ice bin is full of the ice cube and it will stop making the ice automatically.
4. When the “ICE-FULL ” symbol display is on, the unit stops running. And if you move away the ice cube,
the unit will start to make the ice cube again. But it will restart only after 3 minutes interval of compressor
running.
5. During the ice-making process, press the “+” or “-” button to adjust the ice-making process duration
period length, then to change the thickness of the ice cube. Press the “+” or “-” button, the right digit will
ash, the default setting is zero, 1 minute will add or decrease to each ice making process per each
pressing of “+” or “-” button. After 5 second of setting, the new setting will be remembered by the system.
6. The bad water quality will cause the bad quality of ice cube, and reduce the transparency of the ice cube.
AUTOMATIC SELF-CLEANING PROGRAM
START THE SELF-CLEANING PROGRAM: After connecting all of the water pipe, plug on the main power
supply plug, then press “TIMER /CLEAN”button on control panel for more than 5 seconds, to enter the Self-
Cleaning program. And the “ ”symbol will always be on during this period, the left digit will indicate the left
time. The total duration time is 20 minutes for one self-cleaning program. Cancel the self-cleaning program:
It takes about 20 minutes to complete one self-cleaning program. When the program is over, the system
will be in standby mode automatically. And also you can press the “ON/OFF” button on control panel to
cancel the self-cleaning program by force.
TIMER SETTING OPERATION
Delay time range: 1-24 hours, Default time: 1 hour How to set the ON-Timer: During the unit is in standby
mode, press the “TIMER/CLEAN” button to set the ON-Timer. The ON symbol will be on, the number “1”
above the symbol will ash to display the set delay time. During the number ashing, press+” “-”button to
change the delay time of the timer, 1 hour increasing or decreasing per each pressing of “+” or “-” button.
Five seconds after setting, your desired setting will be remembered.
Delay time range: 1-24 hours, Default time: 1 hour How to set the ON-Timer: During the unit is in standby
mode, press the “TIMER/CLEAN” button to set the ON-Timer. The ON symbol will be on, the number “1”
above the symbol will ash to display the set delay time. During the number ashing, press “+” “-”button to
change the delay time of the timer, 1 hour increasing or decreasing per each pressing of “+” or “-” button.
Five seconds after setting, your desired setting will be remembered.
OPERATION