User manual

SOLDERING - DESOLDERING - VACUUM - STATION St 804 SOLDERING
This devicc gives the ambitious DIY-electrician os weil as thc profcssional uscr
the possibility to combine the odvantages of a professional soldering Station
with the requirement of a deoldering sfafion. A festher-weight and
ergonomicolly formed low-voltagc soldering iron, with a streng ceromic
hcaling elcmant and the easy as a soldering tip changcable desoldering top,
wem borir for Chis new devclopment. Working with potential compensation
and full wave logic (switching is done at zero crossing) are given as o matter of
fad.
The Professional Character is supported from accurate temperature adiustment
which is given by digital tcmperaturc control.
Easy handkng, fagether with the very quiet vacuum pump thit unit it fast
integmted into thc working place and soon irreplacwble. Very significant are
the strong desoldering top, where the heat is concentrated at the desoldering
noule and the easy quick - Change -
system for air fiiter and desoldering
tube. Easy handling is guaranteed by the finger swifch and the continuously
adjustable vacuum.
Very convincing are the compacf construction and the enormous productivity
and favourable pricing rotio.
First sfsps:
1, Insert soldering tip to soldering iron.
2. The soldering iron has to be placed on ihe iron stand.
3. Put the plug of the soldering iron into socket (SI).
4. Conned the mains plug to the mains socket (AC 23OV).
5. Switch on thc unif.
6. Adjust the required temperature with the potenliometer.
Operatins
1. Take the soldering iron fmm the stand ofter reaching the required temperature.
2. Lcad the soldering tip to the pieca of werk and add soldering tin.
3. Keep the soldering tip covered with tin at all times, this prcvents the tip of getting
‘blind” (in this care the tin would not Stuck onto the tip).
DESOLDERING
Firsf sfeps:
Contenb:
Station ST 804
(De-jsoldering iron 24V / 6OW
Soldering tip
bsoldwing top
Finger mitch
(De-jsoldering iron stand
Operatlng monual
1. Insert desoldcring top ta soldering iron.
2. The desoldering iron hos to be placed on the iron stand.
3. PUI the plug of the desoldering iron into socket (SI).
4. Connecf the fube to ST 804 (MC).
5. Put the plug of the finger switch into sockef (SW).
6. Connect the mains plug to thc mains socket (AC 23OV).
7. Switch on the unit.
8. Adjust the rcquired temperature with the Potentiometer.
9. Adjust the rcquired vacuum with thc potentiometer.
Operating:
The sales mceipt servcs CIS wormnty document.
Plcasc note: Tbc station requires AC 230V grid voltagc.
Please check, H your local voltage meets
this requfrement.
1. Take the desoldering iron from the stand aftcr reaching the rquired temperature.
2. Put the desoldering noule over the wire of the component to be dcsoldered.
As soon OS the solder tin is amelt thc desoldering process is carricd out by pushing the
finger switch to octivate Ihe vocuum pump, so that the airflow will suck the tin into ihc
tin Container. Ae weil connect the dcsoldering nonle firm with the printed circuit board.
3. Kccp the desoldering nozzle covercd with tin at all times to avoid darnage of surface.
4. Operation only with functional air filterl
In Order to guamntec the full ruction power of the pump, it is necessary to Change
the oir filter ngulary.
Chonqing of fhe desoldering nonle:
Exchanging desoldering noule is quite casy, but should not be done as lang as thc
dcsoldcring iron is hof (danger of scvcre bumingl). Screw out desoldcring noule with
a spanner or plier. Screw in the new dcsoldering noulc.
Cleoning tbe tin confuiner:
Carry out only at cold statel Danger of severe burningl
Removc tin Container from desoldcring fop and cmpty it. Replace felt if necessary.
Chon&tg of fhe oir filter:
Disconncct fhc tube from the unit and pull out the filter ntainer.
The air fiter is inside the fitter retoiner and may be pushcd out with a sharpen Object
‘- --1--I_ ___I___ :. L.. _ __.., ^^_