Mobile Printer SM-T300 SERIES Models: SM-T300 SM-T301 SM-T302 Hardware Manual
Federal Communications Commission Radio Frequency Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Eesti: [Estonian] Käesolevaga kinnitab STAR MICRONICS CO.,LTD. seadme Wireless Device vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele. Ελληνική: ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ STAR MICRONICS CO.,LTD. ΔΗΛΩΝΕΙ ΟΤΙ Wireless Device ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ. [Greek] Slovensky: STAR MICRONICS CO.,LTD.
Operating Precautions Please follow the precautions below to enjoy and maintain the full performance of the printer. ■ Using the Printer ● Some semiconductor devices are easily damaged by static electricity. You should turn the printer “OFF”, before you connect or removed the cable on the rear side, in order to guard the printer against the static electricity. If the printer is damaged by the static electricity, you should turn the printer “OFF”.
Choosing a Place for the Printer Before actually unpacking the printer, you should take a few minutes to think about where you plan to use it. Remember the following points when doing this. 4 Choose a firm, level surface where the printer will not be exposed to vibration. 4 The power outlet you plan to connect to for power should be nearby and unobstructed. 4 Make sure that the printer is close enough to your host computer for you to connect the two.
Table of Contents 1. Introduction...................................................................................5 2. Setting Up the Printer...................................................................6 2.1. Printer & Accessories................................................................................. 6 2.2. Printer Features......................................................................................... 7 2.3. Replacing Paper Roll....................................................
1. Introduction This printer is the ideal solution for Mobile banking system , Retail, point of sales, Credit card Transaction, other traveling and mobile computing etc. The general features of this printer are as follows: ● Pocket size (120 × 132.2 × 58.3 mm) ● Light weight (442 g) for true mobility ● Very silent printing thru direct thermal printing method ● High speed (75 mm/sec, MAX) ● Support Dual Interface 4 RS-232C & Bluetooth Ver.2.1 + EDR 4 RS-232C & Wireless LAN <802.
2. Setting Up the Printer 2.1. Printer & Accessories Your printer box should include these items. If any items are damaged or missing, please contact your dealer for assistance.
2.2. Printer Features ■ Part Name Platen Gear Thermal Head Platen Mechanism Ass’y Feed Button Paper Cover Magnetic Stripe Reader (Option) LCD Error Lamp Open Switch Power Lamp Power Button Protection Film ※ Remove the Protection Film, if it’s not necessary.
2.3. Replacing Paper Roll Cautions : Be sure to use paper rolls that meet the specifications. Do not use paper rolls that have the paper glued to the core because the printer cannot detect the paper end correctly. 1. Before opening the paper cover, ensure no data is being sent to the printer and turn off the power. 2. Open the paper cover by pushing down the open switch and pull it up.
3. Insert a new paper roll as shown. Push down gently on both sides of the paper cover to close it. Ensure the paper cover is securely closed. 4. Tear the excess paper off using the tear bar. 5. Turn the printer power on.
2.4. Power Supply 2.4.1. Specified Battery Charger OUTPUT : DC 8.4 V/0.8 A (CC-CV) 2.4.2. Installing the Battery and the Belt Clip Cautions : 1) Before installing or removing the battery pack, ensure the printer is OFF. 2) If the printer is not used for long period of time, remove the battery pack from the printer. 1. To install battery pack, proceed as follows: - Insert the battery pack in the direction of the arrow. 2. Reverse the order to remove the battery pack. 3. Attach the belt clip as below.
Cautions Concerning Batteries uGeneral Battery Characteristics ● The battery is a consumable and its performance over time will gradually decrease. ● While not in use, the battery will slowly discharge itself. ● Fully charge the battery before using the printer. ● To extend battery life, it is recommended to use a smart energy management solution such as the Auto Power Down Mode available on all Star Micronics Portable Printers.
2.5. Memory Switch Settings 1. Change the Memory switch by this operation. (Refer to Setting Table). POWER button : changing Printer MODE status FEED button : changing OPTION status. 2.
u Press FEED button one time. g You will see present STOP BIT mode in the LCD. Parity Bit g Stop Bit g Press the POWER button one time. (The stop bit has set to 2 stop bit.) 1 Stop Bit g 2 Stop Bit u Press FEED button one time. g You will see present DENSITY mode in the LCD. Stop Bit g Density g Press the POWER button one time. (The density has set to high.
Memory Switch Setting Table Printer Mode 1 Communication Port 2 Baud Rate 3 Data Bit 4 Parity Bit 5 Stop Bit 6 Density 7 Quality 8 BM Sensor 9 BM Sensor Sensitivity 10 Power Down Setting Bluetooth Model RS-232C Bluetooth * 9600 bps 19200 bps 38400 bps 57600 bps * 115200 bps 7 Data bit 8 Data bit * No Parity * Odd Parity Even Parity 1 Stop bit * 2 Stop bit Density Low Density Medium * Density High Low (75 mm/s) * High (50 mm/s) No use * Use Low * Medium 1 Medium 2 High Automatic Setting N
3. Interface 3.1. RS-232C 1 2 3 4 5 This printer has a RS-232C interface and is connected by means of a 5 pin mini USB socket. In the following table, the signals present on the MiniUSB socket are listed: Pin No. 1 2 3 4 5 Name TxD RxD CTS NC. GND Direction Output Input - Function Transmit Data Receive Data Ground Caution : When it removes the communication cable during receiving data, it loses a data. Don’t connect USB mini B cable here.
3.2. Bluetooth Category Specification Bluetooth V2.1+EDR / Class 2 (10 m) 2.4 GHz ISM BAND 57600 bps Fixed 8 Data Bit Fixed No Parity Fixed 1 Stop Bit Fixed SPP (Serial Port Profile) Bluetooth Spec.
3.3. Wireless LAN Category Interface Protocol Communication Mode SSID as default : Specification Network IEEE802.11b/g TCP, UDP, IP, ICMP, ARP, DHCP, PPPoE DNS lookup, DDNS (Dynamic DNS), WEP T2S TCP Server Mode COD TCP Client Mode TCP Server / Client ATC (AT Command Emulation) U2S UDP Star Micronics Caution 1) If more than 1MB of data is sent to the printer over Wireless LAN, the buffer will overflow and the data will be corrupted.
4. Using the Printer 4.1. Control Panel Battery Capacity Status Mode Status POWER ERROR Bluetooth Mode Display Data Transmission Wireless Connection Status : Bluetooth : Wireless LAN : Wireless Disconneciton u Button FEED Button : When the printer is on, paper can be fed manually by pressing and holding theFEED button for more than one second. POWER Button : 1 Pressing and holding the POWER button for 5 seconds or more will turn the power on or off.
4.2. The Self Test The self test procedure will check most of the printer functions. For self test, turn on the power while holding down the FEED button. The Self-Test checks the following : 1) Make sure paper roll has been installed properly. 2) The Self-Test prints the current printer status, which provides the control ROM version and the communication method setting. 3) After printing the current printer status, Self-Test will print a pattern using the built-in character set.
5. Consumable Parts 5.1. Paper Roll Specifications Type : Paper width : Paper thickness : Outer diameter : Inner diameter : Recording side : Thermal Paper 79.5±0.5 mm 65±5 µm Ø50 mm or less Ø12 mm or more Outside of roll Cautions : 1) Do not paste the paper to the core. And the roll paper which has Near end mark printing on its near end is recommended. 2) Chemicals or oil may change the color of paper, or printed Characters may fade. 3) Change of paper color starts from approx 70 °C.
6. Specifications Item Specifications Print method Direct thermal line printing Characters per line 64 cpl (MAX) Character size Resolution Eng. : 9×24 dots, 12×24 dots, 8×16 dots Simplified/Traditional Chinese, Arabic, Cyrillic, Russian, Tukish, Greek, Japanese, Persian, Latin9 and Others upon request. 203 dpi, 8 dots/mm Print width 3-inch (72 mm, 576 dots) Print speed 75 mm / sec (MAX) Optional Characters Dimension 120×132.2×58.
■ Dimensions External Dimensions : 120 mm (width) × 132.2 mm (depth) × 58.
STAR䇭MICRONICS CO.,LTD. Head Office 20-10 Nakayoshida, Suruga-ku, Shizuoka-shi, Shizuoka, 422-8654, Japan Tel. + 81-54-263-1111 Fax. + 81-54-263-1057 STAR Quality Technical Center 18-12 Nakayoshida, Suruga-ku, Shizuoka-shi, Shizuoka, 422-8001, Declaration of Conformity Application of Council Directive(s) R&TTE 1999/5/EC of 9 Mar. 1999 Standard(s) to which Conformity is Declared EN 300 328 V1.7.1 Radio 䋺 EMC 䋺 EN 301 489 -1 V1.8.1 EN 301 489-17 V2.1.
URL: http://www.star-m.
