REVERSE R E W IN D MOTOR OFF N OR M A L FOR W A R D BRAKE REVERSE R E W IN D N OR M A L FOR W A R D PLAY PLAY PAUSE PAUSE MOTOR OFF BRAKE
IMPORTANT TO SAFETY WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. NOTE: This CD player uses the semiconductor laser. To allow you to enjoy music at a stable operation, it is recommended to use this in a room of 5ºC 41ºF - 35ºC 95ºF. CAUTION: 1. Handle the power supply cord carefully Do not damage or deform the power supply cord. If it is damaged or deformed, it may cause electric shock or malfunction when used.
SAFETY INSTRUCTIONS 1. Read Instructions － All the safety and operating receptacles, and the point where they exit from the appliance. instructions should be read before the appliance is 13. Cleaning - The appliance should be cleaned only as operated. 2. Retain Instructions － The safety and operating recommended by the manufacturer. Clean by wiping with a cloth slightly damp with water. instructions should be retained for future reference. Avoid getting water inside the appliance. 3.
FEATURES FADER START / STOP (CUE) must be used alongside a mixer equipped with FADER start control output, such as the NEXT! by STANTON PRO-30. Relay playback Beat counter Large bright LCD Screen can be viewed from wide angles 60 seconds transport protection Auto protection (after 15 minutes with no operating in pause mode, the laser diode will be turned off).
CONTROL UNIT 1 2 REVERSE R E W IN D MOTOR OFF 12 13 3 4 5 6 7 N OR M A L FOR W A R D REVERSE R E W IN D 10 PLAY PAUSE BRAKE MOTOR OFF 14 15 16 17 18 19 20 11 N OR M A L FOR W A R D PLAY BRAKE 21 22 CONNECT TO MAIN UNIT CONNECT TO MAIN UNIT 2 1 23 24 25 CONTROL 2 1 PROGRAM - Depress this button to stop the CD and enter the program mode. Note the word “PROGRAM” is indicated on the display. Select each track to be programmed and press the PROGRAM button between selections.
direction the faster you search through the music. b.Playback (Effect control) - Turn 1/3 of the way left for reverse play. Turn 1/3 of the way right to go back to normal forward play. Turn all the way left for motor off effect all the way rich for brake effect. Release the wheel to go back to normal play. 20. BPM BUTTON - Switches the mode of the display between BPM and pitch. 21.
LCD DISPLAY 1 2 3 4 5 10 11 OPERATING INSTRUCTIONS 6 7 12 13 14 8 15 9 1. OPENING AND CLOSING the Disc Tray and Loading Discs a)Opening and closing the disc tray This operation only works when the power is on. Press the OPEN/CLOSE button(8) to open or close the disc tray. OPEN/CLOSE button(8) are provided on both the main unit and control unit. Press PLAY button to automatically close tray. If tray is not closed after 60 seconds it will close automatically and pause.
11.Loop play You can create a seamless loop between two points continuously. (1) Press PLAY/PAUSE BUTTON (22) so a CD is playing. The PLAY/PAUSE BUTTON’S LED lights (figure 1). (2) Press IN/R. CUE BUTTON (15). This sets the starting point of the SEAMLESS LOOP. The IN/R.CUE LED will light (figure 2). (3) Press OUT/EXIT BUTTON (16) to set desired ending point of the SEAMLESS LOOP. You will know you are in SEAMLESS LOOP mode because IN/R.CUE and OUT/EXIT LEDs will light and flash.
cue) automatically. The following operations are performed on the DJ Mixer. Set CROSS FADER switch to ON. Set FADER START switch to ON. When “A” is in standby mode at cue point, move the CROSS FADER slider from right to left to automatically starting playback instantly. The player’s fader start operation can also be used to produce cross-fader effect. When “B” is in standby mode at cue point, move the CROSS FADER slider from left to right to automatically start playback on “B”.
PREPARATIONS a. Press PLAY/PAUSE BUTTON (22) so that music is playing. PLAY/PAUSE LED will light (figure 11). b. Press MEMORY BUTTON (3) to set a CUE POINT in memory. MEMORY LED will light (figure 12). c. Press desired DIRECT TRACK ACCESS BUTTON (4) (figure 13). d. Press RECALL BUTTON (9) (figure 14). e. Once RECALL LED lights, rapidly press the DIRECT TRACK ACCESS BUTTON (4) previously selected. (figure 15) (3) By rapidly tapping on the SQ Button. a. Be sure you are in playback mode. b. Pressing the IN/R.
