User Manual

Faders / Encoders
• 4 Virtual-pots with 18 segment LED rings (MIDI CC or Incremental CC)
• 1 100mm Motorized fader (MIDI CC)
• 4 Multicolor 8 character alphanumeric LCDs with contrast control (MIDI
SysEX Controllable)
• 1 Cue position display with current deck indicator (MIDI SysEX controllable)
• 4 Velocity sensitive trigger pads (MIDI Note On)
• 46 Momentary backlit push buttons (MIDI Note On)
Buttons / Switches
Displays
Motorized Platter
Motor Type 16 pole, 3 phase, brushless DC motor
Speeds 33 1/3 rpm, 45 rpm
Starting Torque >4.5 kgf.cm
Starting Time 0.2 sec
Braking Time 0.2 sec
Power
Voltage / Amps 24V DC / 3.0
• 13.88 lbs / 6.29 kg
• 3.25˝H x 14.5˝W x 16.75˝L
Dimensions
AudioFaders / Encoders
• 24 Potentiometers (MIDI CC)
• 4 Virtual-pots with 18 segment LED rings (MIDI CC or Incremental CC)
• 4 45mm Linefaders (MIDI CC)
• 1 45mm Crossfader (MIDI CC)
• 1 Rotary encoder (MIDI CC or Incremental CC)
• 4 Multicolor 8 character alphanumeric LCDs with
contrast control (MIDI SysEX controllable)
• 6 9-segment LED meters. One for each channel, one
L&R pair for master (controllable via MIDI)
• 37 Momentary backlit pushbuttons (MIDI Note On)
• 5.96 lbs / 2.71 kg
• 3˝H x 10.75˝W x 16.75˝L
Buttons / Switches
Dimensions
Displays
Frequency Response (20Hz - 20kHz) +/- 0.2dB
THD+N (at 1kHz) 0.013%
Signal to Noise Ratio (A-weighted) 105.1dB
Sampling Rates 44.1kHz, 48kHz, 96kHz
Audio Format 16-bit, 24-bit
Latency (roundtrip) <5 ms
Inputs / Outputs (Max Level)
Phono / Line Input 2 (RCA) Phono / Line switchable, +21dBu unbalanced
Microphone Input 1 (1/4”) @ +9.1dBV unbalanced
Balanced Output 2 (1/4”) @ +27.7dBu
RCA Output 2 (RCA) @ +21.5dBu
Headphone Output 1 (1/4”)
Footswitch Input 1 (1/4”)
Power
Voltage / Amps 12V DC / 3.0
SCS.1m Mix Controller Specifications SCS.1d Deck Specifications
All specications are subject to change without notice.
Master Output
Used for sending
balanced master
audio bus to PA.
Zone Output
Can be used as a
zone (booth) output
for independent
control for monitoring.
Can also be used
as an AUX out for
external FX.
Phono / Line Input
Used to plug in turntables
or CD players for recording
realtime samples or
playback of non digital
audio medium.
Phono / Line and Mic
Trim & Clip LED
Used to adjust the volume
of the Phono / Line and Mic
inputs to avoid clipping and
obtain maximum sound quality.
Footswitch Input
A footswitch may be
connected for toggling
of virtual decks or any
other MIDI control in
software.
Headphone Output
(on front panel)
Used to drive DJ
headphones for cueing and
monitoring of the mix.
Firewire Jacks
Sends audio and
MIDI to and from
the mixer. Multiple
MIDI devices can
be strung together
to create a chain of
SCS components.
Mic Input
Connect a
microphone for
sampling your
voice or getting the
crowd hyped up!
Firewire Jacks
Sends MIDI to and from the deck. Multiple MIDI devices can be
strung together to create a chain of SCS components.