Use and Care Manual

ManualsBrandsStanley ManualsOutdoors15-HP 420 cc Gas Commercial-Duty Chipper Shredder with 4 in. x 3 in. dia. Feed

1 of 12

STANLEY is a registered trademark of The Stanley Works or its affiliates and are used under license by GXi Outdoor Power LLC.

Rev. 9/2010

Owner’s Manual

This manual contains important safety instructions for Chipper/Shredders

READ SAFETY WARNINGS AND OPERATING INSTRUCTIONS CAREFULLY, SAVE THESE INSTRUCTIONS.

Contents:

Warnings & Specifications

Component Identification

Missing Parts Order Form

Assembly

Important Engine Information

Operating Instructions

Maintenance & Storage

Troubleshooting

Warranty & Service

HAVE QUESTIONS OR NEED HELP?

Call our help-line at: [1] 919-550-3259 or go to www.gxioutdoorpower.com

DO NOT RETURN THIS CHIPPER SHREDDER

Date of Purchase: _______________________

Location of Purchase: _______________________

Serial #: _______________________

Model #: _______________________

Have the following information ready when you call us:

2-Way Feed Chipper / Shredder

Summary of content (12 pages)

PAGE 1
2-Way Feed Chipper / Shredder Owner’s Manual This manual contains important safety instructions for Chipper/Shredders READ SAFETY WARNINGS AND OPERATING INSTRUCTIONS CAREFULLY, SAVE THESE INSTRUCTIONS.
PAGE 2
WARNINGS This owner’s manual is considered a permanent part of the chipper shredder and should remain with the chipper shredder if resold. The information and specifications included in this publication were in effect at the time of approval for printing. 8. Never attempt to unclog either the feed intake or discharge opening, remove or empty bag, or inspect and repair the machine while the engine is running. Shut the engine off and wait until all moving parts have come to a complete stop.
PAGE 3
Component Identification Attaching the Chip Collection Bag To attach the bag, place the opening of the bag completely over the discharge chute and hook the metal grommets on two wire hooks located near the base of the engine.  Tighten the draw string securely.  Recoil Starter The starter handle is located on the engine. Pull the starter handle to start engine. Lawn Tractor or ATV Hitch To be used for towing by lawn tractors or ATVs at speeds below 15 mph.
PAGE 4
Missing Parts Request Form Please indicate the part that you are missing: Hardware bag Wheel Kit Other Name Address Date of purchase Model #: Phone Email Serial #: Comments: IMPORTANT: Please include your receipt. Without a receipt, your order will be delayed. You may also email us at: customerservice@gxioutdoorpower.com. Fax: 919-550-3277 If emailing, please scan in your proof of purchase. Other fine products offered by Electric Pressure Washer Rev.
PAGE 5
Assembly Your Responsibility Restrict the use of this power machine to persons who read, understand and follow the warnings and instructions in this manual and on the machine. Not all safety labels shown may apply to your chipper shredder. Preparation 1. 2. 3. 4. 5. 6. Thoroughly inspect the area where the equipment is to be used. Remove all rocks, bottles, cans, or other foreign objects which could be picked up or thrown and cause personal injury or damage to the machine.
PAGE 6
Assembly IMPORTANT: This unit is shipped without gasoline or oil in the engine. Be certain to fill the engine with gasoline and oil as instructed before operating your machine. Required tools: A Philips head screw driver 4. Disconnect The Spark Plug Wire Before setting up your chipper shredder, disconnect the spark plug wire from the spark plug and ground against the engine to prevent inadvertent starting of the machine. This step should be taken as a precaution whenever you are working on this machine.
PAGE 7
Important Engine Information This owner’s manual is considered a permanent part of the power equipment and should remain with the equipment if resold. The information and specifications included in this publication were in effect at the time of approval for printing. GXi Outdoor Power LLC, exclusive marketer of STANLEY heavy duty power equipment, reserves the right to discontinue or change specifications or design at any time without notice and without incurring any obligation whatever.
PAGE 8
Operating Instructions WARNING WARNING: The operation of any chipper shredder can result in foreign objects being thrown into the eyes, which can damage your eyes severely. Always wear the safety glasses provided with this unit or eye shields before chipping or shredding and while performing any adjustments or repairs. Figure 6 Always use the proper personal safety equipment before starting this machine: 1. 2. 3.
PAGE 9
Maintenance & Storage SECTION 5: MAINTAINING YOUR CHIPPER SHREDDER Storing Your Chipper Shredder 1. Clean the equipment thoroughly. Maintenance Schedule Item Before each use Engine oil (Check) 50 hrs or every 3 months 100 hrs or every 6 months 300 hrs or every 1 year Wipe equipment with an oiled rag to prevent rust. 3. Refer to engine manual for correct engine storage instructions 4. Store unit in a clean, dry area. Do not store next to corrosive materials such as fertilizer.
PAGE 10
Maintenance & Storage To Remove, Sharpen or Add Chipper Blades: Your chipper was sent with one blade attached and a spare blade in the hardware bag. The belt life will be extended by operating the chipper with a sharp blade at a time.       Disconnect the spark plug wire and ground against the engine. Remove the blade access hatch and rotate the blade to align with the access hatch.
PAGE 11
Troubleshooting SECTION 6: TROUBLESHOOTING Problem Cause Remedy Engine fails to start 1. Spark plug wire disconnected. 1. Connect wire to spark plug. 2. Fuel tank empty or stale fuel. 2. Fill tank with clean, fresh gasoline. 3. Throttle control lever not in correct starting position. (If Equipped) 3. Move throttle lever to FAST position. 4. Choke not in CHOKE position. (If equipped) 4. Move choke to CHOKE position. 5. Engine not primed. 5. Prime engine. 6. Blocked fuel line. 6.
PAGE 12
Limited Warranty & Service *LENGTH OF WARRANTY: Batteries supplied with applicable products as standard, original equipment are covered by this warranty for a period of 3 months (noncommercial use) or 1 month (commercial/rental use) from the date of original retail product purchase. Consumable parts such as batteries, oil, spark plugs, blades, belts, air filters, carburetors, gloves, hardware bags are not covered by this warranty.