User Manual

9-2 REMOVING OUTSIDE LEVER WITH INTERCHAN-
GEABLE (I.C.) CORE
a. Insert the control Key into the I.C. Core and rotate it
15° clockwise. Pull on the Key to remove the I.C.
Core. Be sure that the I.C. Tailpiece is removed with
the Core.
b. Ensure that the Retaining
Ring and the Anti-Pick Plate
are aligned with the Lever
Catch as shown.
c. Insert an awl or a small
screwdriver through the I.C.
Outside Lever and into the slot in
the Anti-Pick Plate. Depress the
Lever Catch toward the Door
Hinge and slide the I.C. Outside
Lever from the Spindle.
SECURITY
D E V I C E S
OMNILOCK
TWISTED
PAIR
SWITCH
SECTION 6: INSTALL THE STRIKE
a. Mark the location of the Latch Bolt on the Door Frame.
b. Center the Strike over the Latch Bolt Mark and, using the Strike as a template, mark
the Frame.
c. Using the Strike Box as a template, mark the Frame.
d. Mortise the Frame to accept the Strike and Strike Box.
e. Install the Strike Box and the Strike and secure with the Screws.
SECTION 7: PROGRAM THE LOCKSET
IMPORTANT: To avoid unauthorized access, it is important to program a new Programmer ID .
Refer to the OMNILOCK Administrator’s Guide for programming instructions. If the System has been installed on a door before the
required programming information is available, and your system has a keypad, the access Level may be set to Unlocked as follows:
a. Enter the Default Manager ID 2222, at the keypad, the green light will flash.
b. Press 2, the green light will flash.
c. Press and hold the CL key until the green light flashes four times. (The light will flash once when the CL key is pressed,
continue to hold the key until the light flashes three more times.)
d. The System will remain in the Unlocked mode.
SECTION 8: INTERCHANGEABLE CORE
8-1 INTERCHANGEABLE (I.C.) CORE AND TAILPIECE
INSTRUCTIONS FOR ARROW I.C. CORES
Be certain to use the correct Tailpiece with the Core. Six-Pin
Cores use only the “L6” Tailpiece and Seven-Pin Cores use
only the “L7” Tailpiece.
SECTION 9: REMOVAL OF LEVERS
9-1 REMOVING OUTSIDE LEVER WITH STANDARD CYLINDER
a. Insert the Key into the Cylinder and turn 45°
clockwise.
b. Depress the Lever Catch through the
hole in the Outside Lever by using the
Push Pin provided or another suitable
tool.
c. Slide the Outside Lever from the Spindle.
9-3 REMOVING THE INSIDE LEVER
a. Depress the Lever Catch through the
hole in the Inside Lever by using the
Push Pin provided or another suitable
tool.
b. Slide the Inside Lever from the
Spindle.
SECTION 10: REMOTE SWITCH
a. Remote operation of the System may be accomplished by a momentary Switch closure. This
may be desirable for someone monitoring a protected entrance, such as a receptionist.
Momentarily pressing the Switch will cause the System to go through a normal unlock and
lock sequence. If the Switch is held closed, the open time will be extended.
b. Connect a twisted pair of wires from the Terminal Block on the PC Board to a normally open
momentary contact Switch. Plan the route for your wire and the access route through the
door to the PC Board in the OMNILOCK Module. Plan for disconnecting the wires in the Lock
area so that the System can be removed from the door to change the Batteries as required.
1580 JAYKEN WAY
CHULA VISTA, CALIFORNIA 91911
[phone] FAX [phone]
(Website: WWW.OMNILOCK.COM)
PAGE 4 OF 4
STRIKE
BOX
STRIKE
SCREW
#12 X 3/4"
(2 REQ’D)
Copyright 2003 OSI Security Devices Inc. All Rights Reserved.
OMNILOCK is a Registered Trademark of OSI Security Devices Inc. Arrow is a Trademark of Arrow Lock Co. 12831 Rev.A
NOTE:
There are two styles of Tailpieces, one
style has equal length pins and the
other style has unequal length pins.
Use the Tailpiece with equal length
pins if the pins will completely enter the
holes in the Core. Otherwise use the
Tailpiece with unequal length pins and
install the O-ring onto the Tailpiece tab.
8-2 INTERCHANGEABLE (I.C.) CORE INSTALLATION
Insert the applicable I.C. Tailpiece into the I.C. Core. Insert
the Control Key into the I.C. Core and turn it 15°
clockwise. Insert the Core into the I.C. Outside Lever and
turn the Control K
ey 15° counterclockwise to lock the Core
in the Lever. Remove the Control Key.
I.C. TAILPIECE
I.C. CORE
CONTROL
KEY
I.C OUT
SIDE
LEVER
KEY
OUTSIDE
LEVER
PUSH PIN
(PROVIDED)
INTSIDE
LEVER
PUSH PIN
(PROVIDED)
I.C.
CORE
TAILPIECE
(UNEQUAL LENGTH PINS)
TAILPIECE
(EQUAL
LENGTH PINS)
O-RING
OUTSIDE SPINDLE
END VI
EW
ANTI-PICK
PLATE
LEVER
CATCH
OUTSIDE
SPINDLE
RETAINING
RING
+
-
+
-
PAGE 1 OF 4
BATTERY
COVER
BACK
PLATE
GASKET
HOUSING
ASSEMBLY
OUTSIDE
LEVER
I.C.CORE
AA
ALKALINE
BATTERY, 1.5V, 3VOLT
(4 REQ’D)
LOCK
BODY
USE APPLICABLE
TAILPIECE
SEMS,
PAN HEAD,
#4-
40 X 1/4LG
SCREW, FLAT HEAD,
#8-32 X 3/8” LG
(4 REQ’D)
NUT
SCREW, FLAT HEAD,
#8 X 3/4” LG
(2 REQ’D)
SCREW, FLAT HEAD,
#10-32 X 2-1/4”LG
(2 REQ’D)
SCREW, PAN HEAD,
#6 X 3/4”LG
(2 REQ’D)
SCREW, FLAT HEAD,
#12 X 3/4” LG
(2 REQ’D)
CONTROL
KEY
ROSE
OUTSIDE ROSE
INSERT ASSEMBLY
MOTOR
CONNECTOR
FLEXIBLE
ADAPTER
PLATE
DOOR
SPINDLE
LATCH
UNIT
STRIKE BOX
STRIKE
NUT
ROSE
OUTSIDE ROSE
INSERT ASSEMBLY
FLEXIBLE
ADAPTER
PLATE
INSIDE
LEVER
WARNING:
THIS PRODUCT IS
NOT WARRANTED
FOR OUTDOOR USE!
WARNING: CHANGES OR MODIFICATIONS NOT EXPRESSLY
APPROVED BY OSI SECURITY DEVICES COULD VOID THE
USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
NOTE: A DOOR-CLOSER IS HIGHLY RECOMMENDED FOR
USE WITH THIS PRODUCT.
THIS PRODUCT IS NORMALLY FACTORY-PACKED
FOR RIGHT-HAND 1-3/4” THICK DOORS.
TO CHANGE HAND OF LOCK SEE
INSTRUCTION SECTION 3
DO NOT USE ON DOORS THICKER THAN 1-3/4”.
KEY DETECTION
CONNECTOR
(OPTION 1)
I.C. OUTSIDE
LEVER
CYLINDER
KEY
RETAINER
PUSH PIN
(PROVIDED)
RESET BUTTON
MOTOR
CONNECTOR
RED
WIRE
BLACK
WIRE
2 YELLOW
WIRES NO
POLARITY
(OPTION 1 ONLY)
KEY
DETECTION
CONNECTOR
CONNECTOR
SECURITY
DEVICES
OMNILOCK
®
ACCESS CONTROL SYSTEMS
INSTALLATION INSTRUCTIONS FOR OPW2000 SERIES
NON-WEATHERIZED, CYLINDRICAL LOCKSET USING
ARROW™ Q-SERIES LOCK (LEVER)
READ COMPLETE INSTRUCTION BEFORE PROCEEDING.
RIGHT HAND SHOWN
RIGHT HAND
REVERSE
BEVEL
LEFT HAND
REVERSE
BEVEL
LEFT
HAND
RIGHT
HAND
OUTSIDE
INSIDE
OUTSIDE
DOOR HANDLING
DOOR HANDS DETERMINED FROM OUTSIDE
+
-