Operation Manual

CP590 Page 19
The CP590 has the capability to select the Video Input in three ways.
From the menu
1. Press [MENU] twice and move the ShuttlePoint knob to highlight VIDEO INPUT and
press [ENT].
2. A menu appears with 3 options:
ACTIVATE VIDEO, SWITCHING TIMEOUT and
RESTORE DEFAULTS.
. To select the video image highlight
ACTIVATE VIDEO and press [ENT], a popup
window appears with 9 options, see the table below.
Full Screen View 1 : Shows the image from the video camera 1 at full screen.
Full Screen View 2 : Shows the image from the video camera 2 at full screen.
Full View 1 + PIP 2 : Shows the image from the video camera 2 on a window placed over the image from the
video camera 1 at full screen. By moving the ShuttlePoint knob, the PiP (Picture-In-Picture)
image is moved. When the focus is on the PiP image, press [CLR] to close the PiP image.
Full View 2 + PIP 1 : Shows the image from the video camera 1 on a window placed over the image from the
video camera 2 at full screen. By moving the ShuttlePoint knob, the PiP (Picture-In-Picture)
image is moved. When the focus is on the PiP image, press [CLR] to close the PiP image.
PIP View 1 : Shows the image from the video camera 1 on a window placed over the selected CP590
page. By moving the ShuttlePoint knob, the PiP (Picture-In-Picture) image is moved. When
the focus is on the PiP image, press [CLR] to close the PiP image.
PIP View 2 : Shows the image from the video camera 2 on a window placed over the the selected CP590
page. By moving the ShuttlePoint knob, the PiP (Picture-In-Picture) image is moved. When
the focus is on the PiP image, press [CLR] to close the PiP image.
Auto Switch - Full View : Shows wrap around the image from video camera 1 at full screen, the image from video
camera 2 at full screen and the selected CP590 page. The intermittence time is selected
by Switching Timeout item.
Auto Switch - PIP View : Shows wrap around the image from the video camera 1 on a window placed over the
selected CP590 page and the image from the video camera 2 on a window placed over
the selected CP590 page. The intermittence time is selected by Switching Timeout item.
By moving the ShuttlePoint knob, the PiP (Picture-In-Picture) image is moved. When the
focus is on the PiP image, press [CLR] to close the PiP image.
Auto Switch - Full + PIP: Shows wrap around the image from the video camera 1 on a window placed over the image
from the video camera 2 at full screen, the image from the video camera 2 on a window
placed over the image from the video camera 1 at full screen and the selected CP590 page.
The intermittence time is selected by Switching Timeout item. By moving the ShuttlePoint
knob, the PiP (Picture-In-Picture) image is moved. When the focus is on the PiP image,
press [CLR] to close the PiP image.
After the desired option is chosen, the CP590 will show a Warning message with the
instructions to adjust the image from the Video Input. If the user agrees to proceed,
the image from the selected Video Input will be shown.
. To select the intermittence time (the timing to change from Video Input and CP590
display) highlight
SWITCHING TIMEOUT and press [ENT]. The possible choices
are 5,10,30 sec, 1, 5, 10 min.
. To restore the factory defaults for the Input picture adjustment highlight
RESTORE
DEFAULTS and press [ENT]. The message “Ok...” is shown next to the selected
menu item.
NOTE
If the video signal is not present on the video connector, the corresponding item in the menu will
be shown in gray and will not be selectable.
Quick Activation by pressing [CLR] for 1 second
Pressing and holding [CLR] for 1 second from the Chart page display or from any main
page (Navigation, Highway, Celestial, GPS Status, NMEA Display) shows the following
Soft Keys:
.[F
ULL VIEW1] : Shows the image from the video camera 1 at full screen.