Owner's Manual WARNING Exercise can present a health risk. Consult a physician before beginning any exercise program with this equipment. If you feel faint or dizzy, immediately discontinue use of this equipment. Serious bodily injury can occur if this equipment is not assembled and used correctly. Serious bodily injury can also occur if all instructions are not followed. Keep others and pets away from equipment when in use. Always make sure all bolts and nuts are tightened prior to each use.
TABLE OF CONTENTS Page Safety Instructions Before You Begin Equipment Warning & Notice Labels Hardware Identification Chart Assembly Instructions Set Up Instructions Operational Instructions Computer Instructions Storage Page Maintenance Conditioning Guidelines Warm-up and Cool-Down Warranty Product Parts Drawing Parts List Notes Fax/Mail Ordering Form 2 4 5 6 7 12 13 14 18 18 19 20 21 22 23 25 26 SAFETY INSTRUCTIONS WARNING: To reduce the risk of serious injury, read the following Safety Instructions b
CALL US FIRST Customer Service 1(800) 375-7520 www.staminaproducts.com THANK YOU FOR PURCHASING THE Magnetic Fusion 4550 Bike To help you get started, we have pre-assembled most of your Magnetic Fusion 4550 Bike at the factory with the exception of those few parts left unassembled for shipping purposes. Simply follow the few assembly instructions set forth in this manual. With regular workouts, you will be getting your body into shape and be on your way to achieving a happier and healthier lifestyle.
BEFORE YOU BEGIN Thank you for choosing the Magnetic Fusion 4550 Bike. We take great pride in producing this quality product and hope it will provide many hours of quality exercise to make you feel better, look better, and enjoy life to its fullest. It's a proven fact that a regular exercise program can improve your physical and mental health. Too often, our busy lifestyles limit our time and opportunity to exercise.
EQUIPMENT WARNING & NOTICE LABELS This chart is provided to help identify the warning & notice labels on the Magnetic Fusion 4550 Bike. Please take a moment to familiarize yourself with all of the warning & notice labels.
HARDWARE IDENTIFICATION CHART This chart is provided to help identify the hardware used in the assembly process. Place the washers or the ends of the bolts or screws on the circles to check for the correct diameter. Use the small scale to check the length of the bolts and screws. 3/16" 1/4" 5/16" 3/8" 1/2" INCHES 0 1/2 1 1/2 2 1/2 3 1/2 4 1/2 5 1/2 6 in. mm.
ASSEMBLY INSTRUCTIONS Place all parts from the box in a cleared area and position them on the floor in front of you. Remove all packing materials from your area and place them back into the box. Do not dispose of the packing materials until assembly is completed. Read each step carefully before beginning. If you are missing a part please call our toll-free number for assistance 1-800-375-7520 or e-mail us at customerservice@staminaproducts.com.
ASSEMBLY INSTRUCTIONS B. A. (Assembled at the factory) NOTE: Be careful not to damage the PULSE SENSOR WIRES(44) when attaching the HANDRAIL(6) and the SEAT FRAME(5). STEP 4 Refer to illustration A. Attach the HANDRAIL(6) to the SEAT FRAME(5) with CARRIAGE BOLTS (M8x1.25x45mm)(56), ARC WASHERS(M8)(77), LOCK WASHERS(M8)(80), and ACORN NUTS(M8x1.25) (75). STEP 5 Refer to illustration B. Slide the SEAT FRAME(5) onto the REAR FRAME(3) and lock in position with the ADJUSTMENT KNOB(50).
ASSEMBLY INSTRUCTIONS Socket of Pulse Extension Wire(40) STEP 6 Refer to the inset drawing. Plug the PULSE COIL WIRE(42) into the SOCKET of the PULSE EXTENSION WIRE(40) located on the REAR FRAME(3). Clip the GROMMET PLUGS(43) onto both ends of the PULSE COIL WIRE(42). Connect both ends of the PULSE COIL WIRE(42) to the PULSE SENSOR WIRES(44). Push the plugs and excess wires back into the HANDRAIL(6) and secure with the GROMMET PLUGS(43).
ASSEMBLY INSTRUCTIONS STEP 8 NOTE: The RIGHT PEDAL(37) has R stamped on the end of the pedal shaft. The RIGHT PEDAL(37) has right hand threads and is tightened by turning clockwise. The LEFT PEDAL(35) has L stamped on the end of the pedal shaft. The LEFT PEDAL(35) has left hand threads and is tightened by turning counterclockwise. Thread the RIGHT PEDAL(37) into the right side of the CRANK(7) as shown. Tighten the pedal securely.
ASSEMBLY INSTRUCTIONS Socket of Power Wire(86) STEP 9 Run the EXTENSION WIRE on the COMPUTER(27) through the COMPUTER POST(26). Attach the COMPUTER(27) to the COMPUTER POST(26) with ROUND HEAD SCREWS(M5x0.8x12mm)(64). STEP 10 Plug the MOTOR CONTROL WIRE(28) and PULSE PLUG WIRE(39) to the EXTENSION WIRE on the COMPUTER(27). Insert the COMPUTER POST(26) onto the FRONT FRAME(1) and secure with ROUND HEAD BOLTS(M6x1x15mm)(61), LOCK WASHERS(M6)(79), and ARC WASHERS(M6)(76).
SET UP INSTRUCTIONS Place the Magnetic Fusion 4550 Bike in the area where it will be used. It is recommended that the Magnetic Fusion 4550 Bike be placed on an equipment mat. The Magnetic Fusion 4550 Bike is approximately 57 3/4 inches long x 24 3/8 inches wide x 45 1/8 inches tall (max.). (These dimensions may vary up to one inch.) An area 4 feet wide x 7 feet long is required for safe operation of the Magnetic Fusion 4550 Bike.
OPERATIONAL INSTRUCTIONS SEAT ADJUSTMENT Proper seat adjustment is important. There are twelve adjustment holes in the REAR FRAME(3). These adjustment holes allow users to adjust the position of the seat for efficient exercise. 1. Rotate the ADJUSTMENT KNOB(50) counterclockwise until the pin releases when the knob is pulled. Pull the ADJUSTMENT KNOB(50) and slide the SEAT FRAME(5) up or down to desired position.
COMPUTER INSTRUCTIONS Your Magnetic Fusion 4550 Bike utilizes a magnetic braking system to create resistance for your workout. You control the amount and pattern of this resistance by means of the advanced computer console mounted at the center of the handlebar. We recommend that you use this computer console to vary your workout from session to session and note your progress toward your fitness goals.
COMPUTER INSTRUCTIONS PROGRAM NUMBER HEART RATE CONTROL PROGRAMS CALORIE / WATT TIME AGE / TARGET H.R. SPEED / RPM HEART RATE DISTANCE HEART SYMBOL PROGRAM PROFILE LCD DISPLAY INSTRUCTIONS PROGRAM: Displays programs for selection during setup, from P1 to P12. Displays the selected program during exercise. TIME: Displays the time. Counts upward from one second to 99:59 minutes. Counts down from preset value. SPEED/RPM: Displays the current speed from zero to 99.
COMPUTER INSTRUCTIONS PROGRAM DESCRIPTIONS This computer contains 12 different programs. You can preset the program time and the computer will divide the time chosen into 10 intervals. If you do not set the program time in advance, the computer will default to a 30 minute workout time. (P1) MANUAL MANUAL PROGRAM: P1 is a manual program allowing the user to have full manual control of the workload. Use the " " button to increase the load. Use the " " button to decrease the load.
COMPUTER INSTRUCTIONS HEART RATE CONTROL PROGRAMS: P11 and P12 are preset automatic Heart Rate Control Programs. You must input your age and always hold the pulse sensors on the HANDRAIL(6) with both hands when using the Heart Rate Control Programs. P11 is programmed to use 60% of your maximum heart rate as your target heart rate zone workout goal, and P12 is programmed to use 85% of your maximum heart rate as your target heart rate zone workout goal; therefore, P11 will be a less intense workout than P12.
COMPUTER INSTRUCTIONS OPERATION DESCRIPTIONS 1. To stop a running program, press the START / STOP button. In this mode, you can press the START / STOP button again to continue to run the current program. Or, you can use the " / " buttons to select a new program. The function values of DISTANCE and CALORIE will continue to accumulate. 2. When you complete a program, press the START / STOP button to stop the program. You can use the " / " buttons to select a new program.
CONDITIONING GUIDELINES How you begin your exercise program depends on your physical condition. If you have been inactive for several years or are severely overweight, start slowly and increase your workout time gradually. Increase your workout intensity gradually by monitoring your heart rate while you exercise. Remember to follow these essentials: Have your doctor review your training and diet programs. Begin your training program slowly with realistic goals that have been set by you and your physician.
WARM-UP and COOL-DOWN Warm-Up The purpose of warming up is to prepare your body for exercise and to minimize injuries. Warm up for two to five minutes before strength training or aerobic exercising. Perform activities that raise your heart rate and warm the working muscles.
LIMITED WARRANTY MODEL 15-4550 WARRANTY Stamina Products, Inc. warrants that this product will be free from defects in materials and workmanship under normal use, service and proper operation for a period of 90 days on the parts and three years on the frame from the date of the original purchase from an authorized retailer.
PRODUCT PARTS DRAWING FRONT BACK 22
PARTS LIST PART# 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 PART NAME Front Frame Front Stabilizer Rear Frame Rear Stabilizer Seat Frame Handrail Crank Bearing Housing Ball Bearing Inside Bearing Collar Outside Bearing Collar Bearing Washer Bearing Snap Washer Bearing Nut Pulley V-Ribbed Belt Idler Arm Idler Wheel Idler Wheel Spacer Tension Spring Magnetic Unit Eyebolt Tension Bracket Tension Cable Motor Computer Post
PARTS LIST PART# 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 PART NAME Back Cushion Bushing Adjustment Knob Stopper Wheel Leveling Cap Stand Rectangular Plug (30mm x 60mm) Carriage Bolt (M8 x 1.25 x 45mm) Carriage Bolt (M8 x 1.25 x 75mm) Bolt, Button Head (M8 x 1.25 x 40mm) Bolt, Button Head (M10 x 1.5 x 15mm) Bolt, Hex Head (M8 x 1.25 x 80mm) Bolt, Round Head (M6 x 1 x 15mm) Bolt, Flat Head (M8 x 1.
NOTES 25
FAX/MAIL ORDERING FORM Please do not return the product. For your convenience, Stamina's Customer Service Department can be reached by email at customerservice@staminaproducts.com or toll free at 1-800-375-7520 (in the U.S.). Should a part be missing or a defective part found, please call us from 7:30 A.M. to 5:00 P.M. Central Time, Monday through Thursday and 8:00 A.M. to 3:00 P.M. on Friday or fill out the fax sheet ordering form below and fax it to (417) 889-8064.
