Owner's Manual ! WARNING ! Exercise can present a health risk. Consult a physician before beginning any exercise program with this equipment. If you feel faint or dizzy, immediately discontinue use of this equipment. Serious bodily injury can occur if this equipment is not assembled and used correctly. Serious bodily injury can also occur if all instructions are not followed. Keep others and pets away from equipment when in use.
TABLE OF CONTENTS Safety Instructions ...................................... 2 Before You Begin ........................................ 4 Equipment Warning & Notice Labels ........ 5 Hardware Identification Chart .................... 6 Assembly Instructions ................................ 7 Operational Instructions ........................... 13 Storage ....................................................... 16 Maintenance ............................................... Warranty .........................
NEED HELP? CONTACT US FIRST 1 (800) 375-7520 customer.care@staminaproducts.com Hi! From all of us here at Stamina Products, thank you for your purchase. We know that you have big fitness goals in mind and we are here to help you along. Call us, email us, or send us a message on Facebook. Be sure to contact us if you have any questions on your new product.
BEFORE YOU BEGIN Thank you for choosing the inLine® Inversion Chair. We take great pride in producing this quality product and hope it will provide many hours of quality exercise to make you feel better, look better, and enjoy life to its fullest. It's a proven fact that a regular exercise program can improve your physical and mental health. Too often, our busy lifestyles limit our time and opportunity to exercise.
EQUIPMENT WARNING & NOTICE LABELS This chart is provided to help identify the warning and notice labels on the InLine® Inversion Chair. Please take a moment to familiarize yourself with all of the warning and notice labels. Labels are larger than actual size W1 ! WARNING For consumer use only. Failure to follow all warnings and instructions could result in serious injury or death.
HARDWARE IDENTIFICATION CHART This chart is provided to help identify the fasteners used in the assembly process. Place the washers or the ends of the bolts or screws on the circles to check for the correct diameter. Use the small scale to check the length of the bolts and screws. 3/16" 1/4" 5/16" 3/8" 1/2" INCHES 0 0 1/2 10 1 20 1/2 30 40 2 50 1/2 60 3 70 1/2 80 90 4 1/2 100 110 120 5 1/2 130 140 150 MILLIMETERS 6 8 10 6 in. mm.
ASSEMBLY INSTRUCTIONS Place all parts from the box in a cleared area and position them on the floor in front of you. Remove all packing materials from your area and place them back into the box. Do not dispose of the packing materials until assembly is completed. Read each step carefully before beginning. If you are missing a part, please go to staminaproducts.com under the Customer Care section and order the part needed, e-mail us at customer.care@staminaproducts.
ASSEMBLY INSTRUCTIONS STEP 3 Attach the BACK FRAME(5) to the REAR FRAME(3) with BUTTON HEAD BOLTS (M10x1.5x65mm)(41), WASHERS(M10)(52), and NYLOCK NUTS(M10x1.5)(57) on both sides. STEP 4 Place the SWING BAR(9) into the gap in the SEAT FRAME(7), then secure by inserting the SHAFT(12) through the SEAT FRAME(7) and SWING BAR(9). Attach the FRONT PIVOT ARMS(6) to both ends of the SHAFT(12) with BUTTON HEAD BOLTS(M6x1x35mm)(50), ARC WASHERS(M6)(56), and NYLOCK NUTS(M6x1)(59).
ASSEMBLY INSTRUCTIONS STEP 5 Attach the FRONT PIVOT ARMS(6) to the REAR FRAME(3) with BUTTON HEAD BOLTS (M10x1.5x65mm)(41), WASHERS(M10)(52), and NYLOCK NUTS(M10x1.5)(57) on both sides. STEP 6 Attach the SEAT FRAME(7) to the BACK FRAME(5) with BUTTON HEAD BOLT(M10x1.5x90mm)(40), WASHERS(M10)(52), and NYLOCK NUT(M10x1.5)(57). STEP 7 Attach the LINKAGE(8) to the BACK FRAME(5) with BUTTON HEAD BOLT(M8x1.25x85mm)(42), WASHERS(M8)(53), and NYLOCK NUT(M8x1.25)(58).
ASSEMBLY INSTRUCTIONS STEP 8 Refer to detail view A and the illustration below. Attach the ANGLE ADJUSTMENT BELT(16) to the FRONT SUPPORT(2) with BUTTON HEAD BOLT(M8x1.25x60mm)(44), WASHERS(M8)(53), and NYLOCK NUT(M8x1.25)(58). STEP 9 Refer to the bottom view of the illustration below. Align the hook and loop pad on the HINGE WEAR COVER(15) and the SEAT(13), then press them to attach together. STEP 10 Attach the SEAT(13) to the SEAT FRAME(7) with ROUND HEAD BOLTS(M6x1x20mm)(51) and WASHERS(M6)(55).
ASSEMBLY INSTRUCTIONS STEP 11 Attach the SEAT BELT(60) to the BACK FRAME(5) with FLAT HEAD BOLT(M6x1x20mm)(61) and WASHER(M10)(52). CAUTION: Always use the SEAT BELT(60). Make sure the SEAT BELT(60) is securely fastened before inverting. STEP 12 Refer to the Back View of the illustration below. Align the hook and loop pad on the HINGE WEAR COVER(15) and the BACK CUSHION(14), then press them to attach together.
ASSEMBLY INSTRUCTIONS STEP 13 Insert the upper end of the HANDRAIL(4) into the REAR FRAME(3) and secure with BUTTON HEAD BOLT(M8x1.25x40mm)(47). Do no tighten the bolt. Attach the lower end of the HANDRAIL(4) to the REAR FRAME(3) with BUTTON HEAD BOLT(M8x1.25x20mm)(48), BUTTON HEAD BOLT(M8x1.25x65mm)(43), and ARC WASHERS(M8)(54). Tighten the BUTTON HEAD BOLT (M8x1.25x40mm)(47). Repeat on other side. STEP 14 Pull the ADJUSTMENT KNOB(28) and insert the LEG ADJUSTMENT FRAME(10) into the SWING BAR(9).
OPERATIONAL INSTRUCTIONS GENERAL PRECAUTIONS 1. Do not use the InLine® Inversion Chair alone. Always have a helper available in case assistance is needed in recovering from the decline position. 2. Always use the SEAT BELT(60). Make sure the SEAT BELT(60) is securely fastened before inverting. 3. Make sure that the LEG ADJUSTMENT FRAME(10) is properly set for your height. 4. Make sure that the FOAM PADS(36) are holding your feet properly. 5.
OPERATIONAL INSTRUCTIONS LEG HEIGHT ADJUSTMENT Proper adjustment of the LEG ADJUSTMENT FRAME(10) is very important. 1. Loosen the ADJUSTMENT KNOB(28) on the SWING BAR(9). 2. Pull the ADJUSTMENT KNOB(28) and slide the LEG ADJUSTMENT FRAME(10) to adjust. 3. Sit on the machine to make sure you feel comfortable with the FOAM PADS(36). 4. Tighten the ADJUSTMENT KNOB(28) after adjustment. THE SEAT BELT CAUTION: Always use the SEAT BELT(60). Make sure the SEAT BELT(60) is securely fastened before inverting.
OPERATIONAL INSTRUCTIONS USING THE InLine® Inversion Chair 1. Always use the SEAT BELT(60). Make sure the SEAT BELT(60) is securely fastened before inverting. 2. Start by sitting on the machine and leaning back on the BACK CUSHION(14) with your hands at your side, or resting on your thighs. 3. Use the HANDRAILS(4) and both hands to rotate the BACK CUSHION(14) slowly backward until the inversion stopped by the ANGLE ADJUSTMENT BELT(16). 4.
STORAGE 1. To store the InLine® Inversion Chair, simply keep it in a clean dry place. 2. Move the InLine® Inversion Chair by lifting the frame and moving slowly. NOTE: Two people are required to move the InLine® Inversion Chair. MAINTENANCE The safety and integrity designed into the InLine® Inversion Chair can only be maintained when the InLine® Inversion Chair is regularly examined for damage and wear. Special attention should be given to the following: 1.
LIMITED WARRANTY MODEL 55-1550 WARRANTY Stamina Products, Inc. (“Stamina”) warrants to the original purchaser that this product will be free from defects in materials and workmanship that arise under normal use, service, proper assembly and proper operation in accordance with product warnings/instructions for a period of 90 days on the parts and three years on the frame from the date of the original purchase from an authorized retailer.
PRODUCT PARTS DRAWING BACK 18 FRONT
PARTS LIST PART# 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 PART NAME QTY Front Frame Front Support Rear Frame Handrail Back Frame Front Pivot Arm Seat Frame Linkage Swing Bar Leg Adjustment Frame Lever Shaft Seat Back Cushion Hinge Wear Cover Angle Adjustment Belt Round Stand Bumper Sleeve Round Plug (19 mm) Oval Endcap (20 x 60mm) Square Plug (33.4 x 33.
PARTS LIST PART# 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 PART NAME QTY Bolt, Button Head (M8 x 1.25 x 20mm) Bolt, Round Head (M6 x 1 x 55mm) Bolt, Round Head (M6 x 1 x 35mm) Bolt, Round Head (M6 x 1 x 20mm) Washer (M10) Washer (M8) Arc Washer (M8) Washer (M6) Arc Washer (M6) Nylock Nut (M10 x 1.5) Nylock Nut (M8 x 1.
NOTES 21
TO CONTACT CUSTOMER CARE For your convenience, Stamina’s customer care representatives can be reached by email at customer.care@staminaproducts. com or by phone at 1-800-375-7520 (in the U.S.). Our customer care representatives are available Monday through Thursday from 7:30 a.m. until 5:00 p.m., and Friday 8:00 a.m. until 3 p.m. Central Time. ONLINE CUSTOMER CARE customer.care@staminaproducts.com www.staminaproducts.com TELEPHONE CUSTOMER CARE Tel: 1 (800) 375-7520 MAIL STAMINA PRODUCTS, INC.
