Owner's Manual WARNING Exercise can present a health risk. Consult a physician before beginning any exercise program with this equipment. If you feel faint or dizzy, immediately discontinue use of this equipment. Serious bodily injury can occur if this equipment is not assembled and used correctly. Serious bodily injury can also occur if all instructions are not followed. Keep others and pets away from equipment when in use. Always make sure all bolts and nuts are tightened prior to each use.
TABLE OF CONTENTS Page Safety Instructions Before You Begin Equipment Warning & Notice Labels Hardware Identification Chart Assembly Instructions Set Up Instructions Operational Instructions Storage Page 2 4 5 6 7 11 12 14 Maintenance Conditioning Guidelines Warm-Up and Cool-Down Warranty Product Parts Drawing Parts List Notes Fax/Mail Ordering Form 14 15 16 17 18 19 21 22 SAFETY INSTRUCTIONS WARNING: To reduce the risk of serious injury, read the following Safety Instructions before using the Magneti
CALL US FIRST Customer Service 1(800) 375-7520 www.staminaproducts.com THANK YOU FOR PURCHASING THE Magnetic Recumbent 1350 Bike To help you get started, we have pre-assembled most of your Magnetic Recumbent 1350 Bike at the factory with the exception of those few parts left unassembled for shipping purposes. Simply follow the few assembly instructions set forth in this manual.
BEFORE YOU BEGIN Thank you for choosing the Magnetic Recumbent 1350 Bike. We take great pride in producing this quality product and hope it will provide many hours of quality exercise to make you feel better, look better, and enjoy life to its fullest. It's a proven fact that a regular exercise program can improve your physical and mental health. Too often, our busy lifestyles limit our time and opportunity to exercise.
EQUIPMENT WARNING & NOTICE LABELS This chart is provided to help identify the warning & notice labels on the Magnetic Recumbent 1350 Bike. Please take a moment to familiarize yourself with all of the warning & notice labels.
HARDWARE IDENTIFICATION CHART This chart is provided to help identify the hardware used in the assembly process. Place the washers or the ends of the bolts or screws on the circles to check for the correct diameter. Use the small scale to check the length of the bolts and screws. 3/16" 1/4" 5/16" 3/8" 1/2" INCHES 0 1/2 1 1/2 2 1/2 3 1/2 4 1/2 5 1/2 6 in. mm.
ASSEMBLY INSTRUCTIONS Place all parts from the box in a cleared area and position them on the floor in front of you. Remove all packing materials from your area and place them back into the box. Do not dispose of the packing materials until assembly is completed. Read each step carefully before beginning. If you are missing a part please call our toll-free number for assistance 1-800-375-7520 or e-mail us at: customerservice@staminaproducts.
ASSEMBLY INSTRUCTIONS STEP 4 NOTE: Install the HEX BOLTS(M6x1x37mm)(50) as shown in the illustration above. This allows the head of the bolts to fit inside the hex shape holes in the SEAT FRAMES(5, 6). Attach the RIGHT HANDRAIL(8) to the RIGHT SEAT FRAME(6) with HEX BOLTS(M6x1x37mm)(50), ARC WASHERS(M6)(64), LOCK WASHERS(M6)(66), and ACORN NUTS(M6x1)(60). Repeat on the left side. STEP 5 Attach the SEAT CUSHION(41) to the LEFT and RIGHT SEAT FRAMES(5, 6) with ROUND HEAD BOLTS (M6x1x35mm)(51).
ASSEMBLY INSTRUCTIONS A. B. Strap A Metal Fitting Strap B Cable End Bracket Spring Hook STEP 6 Refer to illustration A. Pull the ends of the TENSION CABLE(24) and SENSOR WIRE(28) out of the FRONT FRAME(1). There are two straps attached inside of the METER POST(26) to assist when pulling the SENSOR WIRE(28) and the TENSION CABLE(24) through the METER POST(26). Tie STRAP A to the plug end of the SENSOR WIRE(28). Tie STRAP B to the BRACKET of the TENSION CABLE(24).
ASSEMBLY INSTRUCTIONS STEP 8 NOTE: The RIGHT PEDAL(35) has R stamped on the end of the pedal shaft. The RIGHT PEDAL(35) has right hand threads and is tightened by turning clockwise. The LEFT PEDAL(34) has L stamped on the end of the pedal shaft. The LEFT PEDAL(34) has left hand threads and is tightened by turning counter clockwise. Thread the RIGHT PEDAL(35) to the right side of the CRANK(9) as shown. Tighten the pedal securely. Do the same to attach the LEFT PEDAL(34) to the left side of the CRANK(9).
SET UP INSTRUCTIONS Place the Magnetic Recumbent 1350 Bike in the area where it will be used. It is recommended that the Magnetic Recumbent 1350 Bike be placed on an equipment mat. The Magnetic Recumbent 1350 Bike is approximately 61 3/4 inches long (max.) x 27 1/2 inches wide x 36 inches tall. (These dimensions may vary up to one inch.) An area 4 feet wide x 7 feet long is required for safe operation of the Magnetic Recumbent 1350 Bike.
OPERATIONAL INSTRUCTIONS SEAT ADJUSTMENT Proper seat adjustment is important. There are seven adjustment holes in the REAR FRAME(3). These adjustment holes allow users to adjust the position of the seat for efficient exercise. 1. Unscrew to remove the ADJUSTMENT KNOB(37) from the FRONT FRAME(1). Slide the REAR FRAME (3) to adjust the seat.
OPERATIONAL INSTRUCTIONS USING THE METER POWER ON : Pedal movement or push the button. POWER OFF : Automatic shut off after four minutes of inactivity. MODE/RESET BUTTON: Press to select display functions, include SCAN, TIME, SPEED, DISTANCE, and CALORIES. Press and hold for three seconds to reset all functions to zero. FUNCTIONS: SCAN: Automatically scans each function of TIME, SPEED, DISTANCE, and CALORIES in sequence with change every four seconds.
STORAGE 1. To store the Magnetic Recumbent 1350 Bike, simply keep it in a clean dry place. 2. Adjust the REAR FRAME(3) into the FRONT FRAME(1) to the shortest position. The Magnetic Recumbent 1350 Bike is approximately 39 3/4 inches long x 27 1/4 inches wide x 32 1/4 inches tall. These dimensions will vary. Please measure your Magnetic Recumbent 1350 Bike if exact dimensions are needed. 3. Use two people to lift the Magnetic Recumbent 1350 Bike from the FRONT STABILIZER(2) and REAR STABILIZER(4) to move. 4.
CONDITIONING GUIDELINES How you begin your exercise program depends on your physical condition. If you have been inactive for several years or are severely overweight, start slowly and increase your workout time gradually. Increase your workout intensity gradually by monitoring your heart rate while you exercise. Remember to follow these essentials: Have your doctor review your training and diet programs. Begin your training program slowly with realistic goals that have been set by you and your physician.
WARM-UP and COOL-DOWN Warm-Up The purpose of warming up is to prepare your body for exercise and to minimize injuries. Warm up for two to five minutes before strength training or aerobic exercising. Perform activities that raise your heart rate and warm the working muscles.
LIMITED WARRANTY MODEL 15-1350 WARRANTY Stamina Products, Inc. warrants that this product will be free from defects in materials and workmanship under normal use, service and proper operation for a period of 90 days on the parts and one year on the frame from the date of the original purchase from an authorized retailer.
PRODUCT PARTS DRAWING FRONT Strap A Strap B BACK 18
PARTS LIST PART# 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 PART NAME Front Frame Front Stabilizer Rear Frame Rear Stabilizer Left Seat Frame Right Seat Frame Left Handrail Right Handrail Crank Bearing Housing Ball Bearing Inside Bearing Collar Outside Bearing Collar Bearing Washer Bearing Snap Washer Bearing Nut Pulley V-Ribbed Belt Idler Arm Idler Wheel Idler Wheel Spacer Tension Spring Magnetic Unit Tension Cable Te
PARTS LIST PART# 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 PART NAME Bolt, Button Head (M8 x 1.25 x 15mm) Bolt, Button Head (M10 x 1.5 x 122mm) Bolt, Hex Head (M6 x 1 x 37mm) Bolt, Round Head (M6 x 1 x 35mm) Bolt, Flat Head (M10 x 1.5 x 20mm) Bolt, Flat Head (M10 x 1.5 x 35mm) Screw, Round Head (M5 x 0.8 x 15mm) Screw, Flat Head (M5 x 0.8 x 10mm) Screw, Flat Head (M4 x 15mm) Screw, Big Round Head (M5 x 15mm) Screw, Round Head (M4 x 25mm) Nylock Nut (M10 x 1.
NOTES 21
FAX/MAIL ORDERING FORM Please do not return the product. For your convenience, Stamina's Customer Service Department can be reached by email at customerservice@staminaproducts.com or toll free at 1-800-375-7520 (in the U.S.). Should a part be missing or a defective part found, please call us from 7:30 A.M. to 5:00 P.M. Central Time, Monday through Thursday and 8:00 A.M. to 3:00 P.M. on Friday or fill out the fax sheet ordering form below and fax it to (417) 889-8064.
