User manual: SW V1.0
Table Of Contents
- Table of contents
- 1 General information
- 2 Safety instructions
- 3 Features
- 4 Installation
- 5 Connections and operating elements
- 6 Operating
- 6.1 ‘Setting’ menu
- 6.1.1 Create a new fixture profile
- 6.1.2 Modify a fixture profile
- 6.1.3 Delete a fixture profile
- 6.1.4 Patch a fixture
- 6.1.5 Reverse channel setup
- 6.1.6 Fade mode select
- 6.1.7 Blackout mode select
- 6.1.8 Midi channel select
- 6.1.9 Chase run by inside / outside time
- 6.1.10 Auto remote address
- 6.1.11 Reading from a USB drive
- 6.1.12 Writing to a USB drive
- 6.1.13 Modify password
- 6.1.14 Enable / disable the password
- 6.1.15 Erase all memory
- 6.1.16 Adjust audio input range
- 6.1.17 Channel value display mode
- 6.2 Programming mode
- 6.2.1 Programming a scene
- 6.2.2 Programming a scene with movement
- 6.2.3 Editing a scene
- 6.2.4 Copying a scene
- 6.2.5 Deleting a scene
- 6.2.6 Copying a bank
- 6.2.7 Programming a chase
- 6.2.8 Chase programming from all scenes of a bank
- 6.2.9 Replacing scenes of a chase
- 6.2.10 Adding scenes to a chase
- 6.2.11 Deleting scenes from a chase
- 6.2.12 Deleting a chase
- 6.2.13 Preset programming
- 6.2.14 Preset editing
- 6.2.15 Programming a fixture group
- 6.2.16 Fixture group editing
- 6.2.17 Deleting a fixture group
- 6.2.18 Center programming
- 6.2.19 Center editing
- 6.2.20 Deleting a Center
- 6.2.21 Override programming
- 6.2.22 Override editing
- 6.2.23 CUE programming
- 6.2.24 CUE editing
- 6.2.25 Deleting a Cue
- 6.2.26 Blackout scene programming
- 6.3 Function mode
- 6.4 Fogger operation
- 6.5 Strobe operation
- 6.6 Software update
- 6.1 ‘Setting’ menu
- 7 MIDI functions list
- 8 Notes on creating profiles
- 9 Technical specifications
- 10 Protecting the environment
8 Notes on creating proles
The nished le should use a short name below 8 characters, only use capital letters
and the extension ‘CIF’ (the controller does non support long le name). Otherwise
the controller can’t read the prole information.
Activation of special codes, so that the controller can handle certain channel charac‐
teristics.
ARRT CODE
D = DIMMER DIMMER
P = PAN PAN
PF = PAN FINE PAN FINE in 16 channel mode
T = TILT TILT
TF = TILT FINE TILT FINE in 16 channel mode
G = ALL GOBO CORRELATION CHAN‐
NELS
transmits all gobo correlation channels
to the gobo preset
C = ALL COLOR CORRELATION CHAN‐
NELS
transmits all colour correlation channels
to the colour preset
N = ETCAETERAS CHANNELS other channels should be signed with N
The channel display message should not be longer than 4 capital letters, underscore
or number, and must be bracketed by double quotation marks. Don’t use blanks for a
shorter le name than 4 characters.
You’d better input in English mode. Make sure that all the input characters are DBC
but not SBC case.
“DIM” – correct
“DIM ” – wrong - because of the blank
“dim” “DIm” – wrong - because of using lower case characters
‘ ‘DIM’ ’ – wrong - because of the SBC double quotation marks
Store the prole that you want to input into the controller in the root direc‐
tory of the CF card. In case the CF card gets the drive letter ‘F’, the path must
read: ‘F:\DIR2402\IM-1200S’. The CF card must be FAT16 formatted, by no
means FAT32 formatted.
Maximum 24 channels, no character repetition.
PROFILE.CIF (as the prole cyclostyle)
IM-1200S.CIF is the prole of ACME
IM-1200S
DMX CHANNEL LIST
Notes on creating proles
DMX controller
60