User manual: SW V1.0
Table Of Contents
- Table of contents
- 1 General information
- 2 Safety instructions
- 3 Features
- 4 Installation
- 5 Connections and operating elements
- 6 Operating
- 6.1 ‘Setting’ menu
- 6.1.1 Create a new fixture profile
- 6.1.2 Modify a fixture profile
- 6.1.3 Delete a fixture profile
- 6.1.4 Patch a fixture
- 6.1.5 Reverse channel setup
- 6.1.6 Fade mode select
- 6.1.7 Blackout mode select
- 6.1.8 Midi channel select
- 6.1.9 Chase run by inside / outside time
- 6.1.10 Auto remote address
- 6.1.11 Reading from a USB drive
- 6.1.12 Writing to a USB drive
- 6.1.13 Modify password
- 6.1.14 Enable / disable the password
- 6.1.15 Erase all memory
- 6.1.16 Adjust audio input range
- 6.1.17 Channel value display mode
- 6.2 Programming mode
- 6.2.1 Programming a scene
- 6.2.2 Programming a scene with movement
- 6.2.3 Editing a scene
- 6.2.4 Copying a scene
- 6.2.5 Deleting a scene
- 6.2.6 Copying a bank
- 6.2.7 Programming a chase
- 6.2.8 Chase programming from all scenes of a bank
- 6.2.9 Replacing scenes of a chase
- 6.2.10 Adding scenes to a chase
- 6.2.11 Deleting scenes from a chase
- 6.2.12 Deleting a chase
- 6.2.13 Preset programming
- 6.2.14 Preset editing
- 6.2.15 Programming a fixture group
- 6.2.16 Fixture group editing
- 6.2.17 Deleting a fixture group
- 6.2.18 Center programming
- 6.2.19 Center editing
- 6.2.20 Deleting a Center
- 6.2.21 Override programming
- 6.2.22 Override editing
- 6.2.23 CUE programming
- 6.2.24 CUE editing
- 6.2.25 Deleting a Cue
- 6.2.26 Blackout scene programming
- 6.3 Function mode
- 6.4 Fogger operation
- 6.5 Strobe operation
- 6.6 Software update
- 6.1 ‘Setting’ menu
- 7 MIDI functions list
- 8 Notes on creating profiles
- 9 Technical specifications
- 10 Protecting the environment
3. Automatic mode
1. Press the [BANK] button and turn jog wheel # 1 to select the desired bank 1 –
60.
2. Press the [AUTO/DEL] button to call up the automatic mode. The ‘AUTO’ LED
lights up.
3. Turn jog wheel # 3 oder # 4 to adjust the current Fade Time or Wait Time.
The FADE TIME value determines in what time moving equipment
such as Moving Heads complete a change from one scene to the next.
The setting range is 0 – 30 s.
The WAIT TIME value determines the display duration for this scene.
The setting range is 0.1 s – 5 min.
Or press the [TAP/INSERT] button to adjust the speed of the automatic run
down of scenes.
If you press the [TAP/INSERT] button to adjust the speed, the display dura‐
tion of the scenes is set by the interval of twice pressing the [TAP/INSERT]
button. This two-time pressing must happen within 10 minutes. The interval
measured by the device is briey shown in the display.
6.3.2 Running a Chase
Before you can run a chase, rst nish a possibly active scene from one of
the memory banks by pressing all those buttons whose LEDs still light up
permanently. Otherwise, you can't exit the BANK function and thus not start
any other function.
1. Manual mode
1. Press the [CHASE] button. Turn jog wheel # 1 to select the memory page on
which the desired Chase is stored. Now the LEDs of those number buttons
[1 – 20] where Chases are stored are ashing. Additionally, the ‘MANUAL’ LED
should light up. Otherwise press the [MANUAL/REC] button to call up the
manual mode.
Operating
DMX controller
52