User manual: SW V1.0
Table Of Contents
- Table of contents
- 1 General information
- 2 Safety instructions
- 3 Features
- 4 Installation
- 5 Connections and operating elements
- 6 Operating
- 6.1 ‘Setting’ menu
- 6.1.1 Create a new fixture profile
- 6.1.2 Modify a fixture profile
- 6.1.3 Delete a fixture profile
- 6.1.4 Patch a fixture
- 6.1.5 Reverse channel setup
- 6.1.6 Fade mode select
- 6.1.7 Blackout mode select
- 6.1.8 Midi channel select
- 6.1.9 Chase run by inside / outside time
- 6.1.10 Auto remote address
- 6.1.11 Reading from a USB drive
- 6.1.12 Writing to a USB drive
- 6.1.13 Modify password
- 6.1.14 Enable / disable the password
- 6.1.15 Erase all memory
- 6.1.16 Adjust audio input range
- 6.1.17 Channel value display mode
- 6.2 Programming mode
- 6.2.1 Programming a scene
- 6.2.2 Programming a scene with movement
- 6.2.3 Editing a scene
- 6.2.4 Copying a scene
- 6.2.5 Deleting a scene
- 6.2.6 Copying a bank
- 6.2.7 Programming a chase
- 6.2.8 Chase programming from all scenes of a bank
- 6.2.9 Replacing scenes of a chase
- 6.2.10 Adding scenes to a chase
- 6.2.11 Deleting scenes from a chase
- 6.2.12 Deleting a chase
- 6.2.13 Preset programming
- 6.2.14 Preset editing
- 6.2.15 Programming a fixture group
- 6.2.16 Fixture group editing
- 6.2.17 Deleting a fixture group
- 6.2.18 Center programming
- 6.2.19 Center editing
- 6.2.20 Deleting a Center
- 6.2.21 Override programming
- 6.2.22 Override editing
- 6.2.23 CUE programming
- 6.2.24 CUE editing
- 6.2.25 Deleting a Cue
- 6.2.26 Blackout scene programming
- 6.3 Function mode
- 6.4 Fogger operation
- 6.5 Strobe operation
- 6.6 Software update
- 6.1 ‘Setting’ menu
- 7 MIDI functions list
- 8 Notes on creating profiles
- 9 Technical specifications
- 10 Protecting the environment
5. Rotate jog wheel # 1 to select the bank that contains the scene that you want
to insert. Press the number button [1 – 20] of the scene to be added to the
chase in the current step.
6. Turn jog wheels # 3 & # 4 to adjust the FADE and WAIT TIME for the current
scene. If you don't adjust these settings, the device will take over the most
recently used values for FADE TIME and WAIT TIME.
7. Press the [MANUAL/REC] button. All LEDs ash three times and thus indicate
the successful replacement of a scene.
8. Repeat steps 4–7 to replace additional scenes.
6.2.10 Adding scenes to a chase
1. Call up the programming mode.
2. Press the [CHASE] button. Turn jog wheel # 1 to select the number of the
memory page on which the chase you want to change has been saved.
3. Press the number button [1 – 20] where the desired chase is stored. The LED of
the [BANK] button lights up and the display shows the number and the chase
parameters for BANK, SCENE, STEP, FADE and WAIT. Additionally, the LEDs of
those number buttons [1 – 20] are ashing, where scenes have already been
assigned to in the respectively displayed bank.
4. Turn jog wheel # 2 to select the position (Step) where you want to add a scene.
5. Press the [TAP/INSERT] button to insert a scene after the current position.
Operating
DMX controller
38