User manual: SW V1.0
Table Of Contents
- Table of contents
- 1 General information
- 2 Safety instructions
- 3 Features
- 4 Installation
- 5 Connections and operating elements
- 6 Operating
- 6.1 ‘Setting’ menu
- 6.1.1 Create a new fixture profile
- 6.1.2 Modify a fixture profile
- 6.1.3 Delete a fixture profile
- 6.1.4 Patch a fixture
- 6.1.5 Reverse channel setup
- 6.1.6 Fade mode select
- 6.1.7 Blackout mode select
- 6.1.8 Midi channel select
- 6.1.9 Chase run by inside / outside time
- 6.1.10 Auto remote address
- 6.1.11 Reading from a USB drive
- 6.1.12 Writing to a USB drive
- 6.1.13 Modify password
- 6.1.14 Enable / disable the password
- 6.1.15 Erase all memory
- 6.1.16 Adjust audio input range
- 6.1.17 Channel value display mode
- 6.2 Programming mode
- 6.2.1 Programming a scene
- 6.2.2 Programming a scene with movement
- 6.2.3 Editing a scene
- 6.2.4 Copying a scene
- 6.2.5 Deleting a scene
- 6.2.6 Copying a bank
- 6.2.7 Programming a chase
- 6.2.8 Chase programming from all scenes of a bank
- 6.2.9 Replacing scenes of a chase
- 6.2.10 Adding scenes to a chase
- 6.2.11 Deleting scenes from a chase
- 6.2.12 Deleting a chase
- 6.2.13 Preset programming
- 6.2.14 Preset editing
- 6.2.15 Programming a fixture group
- 6.2.16 Fixture group editing
- 6.2.17 Deleting a fixture group
- 6.2.18 Center programming
- 6.2.19 Center editing
- 6.2.20 Deleting a Center
- 6.2.21 Override programming
- 6.2.22 Override editing
- 6.2.23 CUE programming
- 6.2.24 CUE editing
- 6.2.25 Deleting a Cue
- 6.2.26 Blackout scene programming
- 6.3 Function mode
- 6.4 Fogger operation
- 6.5 Strobe operation
- 6.6 Software update
- 6.1 ‘Setting’ menu
- 7 MIDI functions list
- 8 Notes on creating profiles
- 9 Technical specifications
- 10 Protecting the environment
4. Now press the [FIXTURE] button and then the number button [1 – 20] for that
device participating in the scene whose settings or eect you want to change.
5. Now you can move the faders to change the functions of each channel. ‘Pan’ &
‘Tilt’ can also be adjusted using jog wheels # 1–# 4, or use the [MOVEMENT]
button to utilize the MOVEMENT function.
6. If desired, repeat steps 4–5 to change the settings of other participating units
in the scene. But then don't forget to deselect the previously edited device by
pressing its number button [1 – 20].
7. Then press the [MANUAL/REC] button to initiate the saving of the changed
scene. The LEDs of the buttons CUE, OVERRIDE, CENTER, FIXTURE GROUP,
PRESET, CHASE, BANK and BLACK OUT are ashing.
8. Press the [BANK] button.
9. Press the corresponding number button [1 – 20] to either save the edited scene
as a new scene, or to overwrite the original. All LEDs will ash three times
briey to indicate the successful saving. The display then shows the number of
the bank along with the number of the just saved scene.
10. Repeat steps 2-9 to edit additional scenes.
If you select dierent scenes in steps 3 and 9, the original scene is not
changed.
6.2.4 Copying a scene
1. Call up the programming mode.
2. Press the [BANK] button and turn Jog wheel # 1 to select the bank, from which
you want to copy a scene.
3. Press the number button [1 – 20] to select the scene to be copied. The scene is
displayed now.
Operating
DMX Invader 2420 MK II
33