User manual: SW V1.0
Table Of Contents
- Table of contents
- 1 General information
- 2 Safety instructions
- 3 Features
- 4 Installation
- 5 Connections and operating elements
- 6 Operating
- 6.1 ‘Setting’ menu
- 6.1.1 Create a new fixture profile
- 6.1.2 Modify a fixture profile
- 6.1.3 Delete a fixture profile
- 6.1.4 Patch a fixture
- 6.1.5 Reverse channel setup
- 6.1.6 Fade mode select
- 6.1.7 Blackout mode select
- 6.1.8 Midi channel select
- 6.1.9 Chase run by inside / outside time
- 6.1.10 Auto remote address
- 6.1.11 Reading from a USB drive
- 6.1.12 Writing to a USB drive
- 6.1.13 Modify password
- 6.1.14 Enable / disable the password
- 6.1.15 Erase all memory
- 6.1.16 Adjust audio input range
- 6.1.17 Channel value display mode
- 6.2 Programming mode
- 6.2.1 Programming a scene
- 6.2.2 Programming a scene with movement
- 6.2.3 Editing a scene
- 6.2.4 Copying a scene
- 6.2.5 Deleting a scene
- 6.2.6 Copying a bank
- 6.2.7 Programming a chase
- 6.2.8 Chase programming from all scenes of a bank
- 6.2.9 Replacing scenes of a chase
- 6.2.10 Adding scenes to a chase
- 6.2.11 Deleting scenes from a chase
- 6.2.12 Deleting a chase
- 6.2.13 Preset programming
- 6.2.14 Preset editing
- 6.2.15 Programming a fixture group
- 6.2.16 Fixture group editing
- 6.2.17 Deleting a fixture group
- 6.2.18 Center programming
- 6.2.19 Center editing
- 6.2.20 Deleting a Center
- 6.2.21 Override programming
- 6.2.22 Override editing
- 6.2.23 CUE programming
- 6.2.24 CUE editing
- 6.2.25 Deleting a Cue
- 6.2.26 Blackout scene programming
- 6.3 Function mode
- 6.4 Fogger operation
- 6.5 Strobe operation
- 6.6 Software update
- 6.1 ‘Setting’ menu
- 7 MIDI functions list
- 8 Notes on creating profiles
- 9 Technical specifications
- 10 Protecting the environment
Number button DMX address Number button DMX address
4 activates unit
with
DMX address 73 14 activates unit
with
DMX address 313
5 activates unit
with
DMX address 97 15 activates unit
with
DMX address 337
6 activates unit
with
DMX address 121 16 activates unit
with
DMX address 361
7 activates unit
with
DMX address 145 17 activates unit
with
DMX address 385
8 activates unit
with
DMX address 169 18 activates unit
with
DMX address 409
9 activates unit
with
DMX address 193 19 activates unit
with
DMX address 432
10 activates unit
with
DMX address 217 20 activates unit
with
DMX address 457
Enter the programming mode by holding down the [PROGRAM] button for 2 sec‐
onds. The LED of the [PROGRAM] button ashes when the programming mode is acti‐
vated.
Press the [ESC/CLEAR] button to abort a running programming.
Hold the [PROGRAM] button again for 2 seconds to exit the programming mode. The
LED of the [PROGRAM] button goes o then.
6.2.1 Programming a scene
1. Call up the programming mode.
2. The LED of the [FIXTURE] button should light up now. Otherwise, press the
[FIXTURE] button. Press the number buttons [1 – 20] to select one or multiple
devices to be used to create the scene.
To call any number of devices with consecutive numbers press the
rst and last number button of the desired set of devices simultane‐
ously.
3. Now use the faders [1–24] the set the desired values for each channel man‐
ually. Of course you can also use jog wheels # 1 & # 2 to adjust [PAN] &
[PAN FINE], or Jog wheel # 3 & # 4 to control [TILT] & [TILT FINE].
Operating
DMX controller
30