User manual: SW V1.0
Table Of Contents
- Table of contents
- 1 General information
- 2 Safety instructions
- 3 Features
- 4 Installation
- 5 Connections and operating elements
- 6 Operating
- 6.1 ‘Setting’ menu
- 6.1.1 Create a new fixture profile
- 6.1.2 Modify a fixture profile
- 6.1.3 Delete a fixture profile
- 6.1.4 Patch a fixture
- 6.1.5 Reverse channel setup
- 6.1.6 Fade mode select
- 6.1.7 Blackout mode select
- 6.1.8 Midi channel select
- 6.1.9 Chase run by inside / outside time
- 6.1.10 Auto remote address
- 6.1.11 Reading from a USB drive
- 6.1.12 Writing to a USB drive
- 6.1.13 Modify password
- 6.1.14 Enable / disable the password
- 6.1.15 Erase all memory
- 6.1.16 Adjust audio input range
- 6.1.17 Channel value display mode
- 6.2 Programming mode
- 6.2.1 Programming a scene
- 6.2.2 Programming a scene with movement
- 6.2.3 Editing a scene
- 6.2.4 Copying a scene
- 6.2.5 Deleting a scene
- 6.2.6 Copying a bank
- 6.2.7 Programming a chase
- 6.2.8 Chase programming from all scenes of a bank
- 6.2.9 Replacing scenes of a chase
- 6.2.10 Adding scenes to a chase
- 6.2.11 Deleting scenes from a chase
- 6.2.12 Deleting a chase
- 6.2.13 Preset programming
- 6.2.14 Preset editing
- 6.2.15 Programming a fixture group
- 6.2.16 Fixture group editing
- 6.2.17 Deleting a fixture group
- 6.2.18 Center programming
- 6.2.19 Center editing
- 6.2.20 Deleting a Center
- 6.2.21 Override programming
- 6.2.22 Override editing
- 6.2.23 CUE programming
- 6.2.24 CUE editing
- 6.2.25 Deleting a Cue
- 6.2.26 Blackout scene programming
- 6.3 Function mode
- 6.4 Fogger operation
- 6.5 Strobe operation
- 6.6 Software update
- 6.1 ‘Setting’ menu
- 7 MIDI functions list
- 8 Notes on creating profiles
- 9 Technical specifications
- 10 Protecting the environment
6.1.9 Chase run by inside / outside time
In this menu you can select whether the chase run is controlled by the time
values used during programming the individual scenes, or the timing
should be determined only during the chase run.
1. Call up the main menu.
2. Turn jog wheel # 1 until ‘09. Chase run by inside/outside time’ is displayed. Press
the [ENTER / MAIN MENU] button to activate this function.
3. Rotate jog wheel # 2 to select ‘[inside time]’ or ‘[outside time]’ . If ‘[inside time]’
is selected, the chase run is controlled by the time values used during pro‐
gramming the individual scenes. If ‘[outside time]’ is selected, the timing can
be freely adjusted during the chase run.
4. Press the [ENTER / MAIN MENU] button to conrm, all LEDs blink three times.
Then, the device will quit this submenu.
6.1.10 Auto remote address
Using this function, compatible moving heads can be addressed via control
panel. Then you don't have to set the address on the device. Non-compliant
devices ignore this function. For compatibility issues, please read the
manual of the respective equipment.
1. Call up the main menu.
2. Turn jog wheel # 1 until ‘10. Auto remote address’ is displayed. Press the
[ENTER / MAIN MENU] button to activate this function.
3. Turn jog wheel # 2 to change the default setting ‘[NO]’ to ‘[Yes]’ . If the display
shows ‘[NO]’ and you press the [ENTER / MAIN MENU] button, the unit will close
this submenu. If the display shows ‘[YES]’ and you press the
[ENTER / MAIN MENU] button, the address dialogue opens up.
Operating
DMX Invader 2420 MK II
23