User manual: SW V1.0
Table Of Contents
- Table of contents
- 1 General information
- 2 Safety instructions
- 3 Features
- 4 Installation
- 5 Connections and operating elements
- 6 Operating
- 6.1 ‘Setting’ menu
- 6.1.1 Create a new fixture profile
- 6.1.2 Modify a fixture profile
- 6.1.3 Delete a fixture profile
- 6.1.4 Patch a fixture
- 6.1.5 Reverse channel setup
- 6.1.6 Fade mode select
- 6.1.7 Blackout mode select
- 6.1.8 Midi channel select
- 6.1.9 Chase run by inside / outside time
- 6.1.10 Auto remote address
- 6.1.11 Reading from a USB drive
- 6.1.12 Writing to a USB drive
- 6.1.13 Modify password
- 6.1.14 Enable / disable the password
- 6.1.15 Erase all memory
- 6.1.16 Adjust audio input range
- 6.1.17 Channel value display mode
- 6.2 Programming mode
- 6.2.1 Programming a scene
- 6.2.2 Programming a scene with movement
- 6.2.3 Editing a scene
- 6.2.4 Copying a scene
- 6.2.5 Deleting a scene
- 6.2.6 Copying a bank
- 6.2.7 Programming a chase
- 6.2.8 Chase programming from all scenes of a bank
- 6.2.9 Replacing scenes of a chase
- 6.2.10 Adding scenes to a chase
- 6.2.11 Deleting scenes from a chase
- 6.2.12 Deleting a chase
- 6.2.13 Preset programming
- 6.2.14 Preset editing
- 6.2.15 Programming a fixture group
- 6.2.16 Fixture group editing
- 6.2.17 Deleting a fixture group
- 6.2.18 Center programming
- 6.2.19 Center editing
- 6.2.20 Deleting a Center
- 6.2.21 Override programming
- 6.2.22 Override editing
- 6.2.23 CUE programming
- 6.2.24 CUE editing
- 6.2.25 Deleting a Cue
- 6.2.26 Blackout scene programming
- 6.3 Function mode
- 6.4 Fogger operation
- 6.5 Strobe operation
- 6.6 Software update
- 6.1 ‘Setting’ menu
- 7 MIDI functions list
- 8 Notes on creating profiles
- 9 Technical specifications
- 10 Protecting the environment
6.1.6 Fade mode select
Here you can congure for which channels programmed fade times are
considered in automatic mode shows.
1. Call up the main menu.
2. Turn jog wheel # 1 until ‘06. Fade mode select’ is displayed. Press the
[ENTER / MAIN MENU] button to activate this function.
3. Turn jog wheel # 2 to switch from the default setting ‘[only pan/tilt]’ to ‘[pan/
tilt + CH select]’ or ‘[all channel]’ .
4. Press the [ENTER / MAIN MENU] button to conrm the setting. If you've selected
‘[all channel]’ or ‘[only pan/tilt]’ all LEDs blink three times. Then, the device will
quit this submenu.
If you've selected ‘[pan/tilt + CH select]’ and conrmed by pressing the
[ENTER / MAIN MENU] button, you can then use the number buttons [1– 20] to
select the device for which you can switch selected channels in the ‘FADE’ or
‘NORMAL’ mode Select the desired channel using jog wheel # 2, while
switching is done via jog wheel # 4.
Some channel functions can not be changed.
5. Press the [ESC / CLEAR] button to return to the previous menu level.
Operating
DMX Invader 2420 MK II
21