Manual

STACK-ON PRODUCTS CO.
P.O. BOX 489, WAUCONDA, IL 60084
IMPORTANT
Keep keys and combination number in a secure place, away from
children. Keep this record of your key number and combination in a
secure place separate from your safe. To order a replacement key set,
follow the instructions on the aached form.
TAB
A "Trouble Key" has been provided in case you have forgoen or
lost your security code. To open the safe using the trouble key
follow the steps below:
4. Enter your new security code following the instructions for
entering your security code
3. Keep the door open until you have entered a new security
code. Before entering your new code, remove the key and screw
the cover back in place.
2. Insert the key in the key hole and turn
clockwise 1/4 turn (until stopped) in order
to unlock the safe. Rotate the handle and
open the door.
1. Remove the cover by pressing the tab and
turning the cover as shown in the
illustration. e lock can hang by the
connecting cable while unlocking the safe.
To turn the "Beep" sound on, enter the code 66.
To enter your own security code you will need to follow the
steps listed below:
NOTE: When changing the baery, always hold the baery
connecting cap while disconnecting or aaching the baery. Do
not pull on the wires. Doing this could cause the power supply to
become disconnected from the lock.
is safe uses one 9V alkaline baery. Under normal use, baeries
will last about 1 year.
When the baery is low and you press a buon on the keypad, a
red light will come on warning you that the baery is low.
To test the baeries, enter your security code. If the baeries are
low the red light will come on momentarily.
To replace the baery, remove the cover by pressing the tab and
turning the cover as shown in the illustration. Replace the old
baery and screw the cover back in place.
You can turn o the "Beep" sound of the keypad by entering the
code 633.
1. Aer opening the electronic safe (with the preset factory
code of 1, 5, 9, #) locate the small red red buon on the inside
of the door near the hinge.
2. Press the red buon and then release it, you will hear a beep.
e yellow light on the faceplate will be activated and will stay
on for a period of time that should allow you to enter your
code. You can only enter your code while the yellow light is on.
If the code fails, go through steps 1 and 2 again. If the code
works successfully record your combination number on the
front of this form or somewhere in your records, then you
should lock the safe.
When you open the safe in the future enter the security code
you have set followed by the " # " symbol.
If the incorrect security code is entered 3 times you will have
an automatic lockout for 20 seconds before you can try your
code again.
If the incorrect security code is entered 3 additional times there
will be a 5-minute lockout before the code can be tried again.
With the door open and the yellow light on, enter your own
personal security code, which can be 3 - 8 digits long, and
conrm your new code by pressing the " " symbol on the
electronic touch pad. Before you close the door, try the new
security code to make sure the lock releases the handle so you
can turn it and retract the live action bolts. DO NOT SHUT
THE DOOR UNTIL YOU HAVE CONFIRMED THAT
YOUR NEW SECURITY CODE HAS BEEN ENTERED
CORRECTLY.
SECURING THE SAFE
BATTERY REPLACEMENT
TROUBLE KEY
TURNING THE KEYPAD SOUND OFF/ON
ENTERING YOUR SECURITY CODE
e shelving can be installed by locating the shelf clips to the
desired locations and seing the shelf in place.
MODELS WITH OPTIONAL SHELVING
NOTE: e scope stand-o will function properly for many
combinations of guns with scopes.
Screw the scope stand-o into the pilot hole of the barrel rest.
INSTALLATION OF SCOPE STAND-OFF
40253-1205
2
12