Datasheet

DocID025644 Rev 3 65/135
STM32F401xD STM32F401xE Electrical characteristics
114
6.3.6 Supply current characteristics
The current consumption is a function of several parameters and factors such as the
operating voltage, ambient temperature, I/O pin loading, device software configuration,
operating frequencies, I/O pin switching rate, program location in memory and executed
binary code.
The current consumption is measured as described in Figure 19: Current consumption
measurement scheme.
All the run-mode current consumption measurements given in this section are performed
with a reduced code that gives a consumption equivalent to CoreMark code.
Typical and maximum current consumption
The MCU is placed under the following conditions:
• All I/O pins are in input mode with a static value at VDD or VSS (no load).
• All peripherals are disabled except if it is explicitly mentioned.
• The Flash memory access time is adjusted to both f
HCLK
frequency and VDD ranges
(refer to Table 15: Features depending on the operating power supply range).
• The voltage scaling is adjusted to f
HCLK
frequency as follows:
– Scale 3 for f
HCLK
≤ 60 MHz
– Scale 2 for 60 MHz < f
HCLK
≤ 84 MHz
• The system clock is HCLK, f
PCLK1
= f
HCLK
/2, and f
PCLK2
= f
HCLK
.
• External clock is 4 MHz and PLL is on
• The maximum values are obtained for V
DD
= 3.6 V and a maximum ambient
temperature (T
A
), and the typical values for T
A
= 25 °C and V
DD
= 3.3 V unless
otherwise specified.
I
RUSH
(2)
InRush current on
voltage regulator power-
on (POR or wakeup from
Standby)
- 160 200 mA
E
RUSH
(2)
InRush energy on
voltage regulator power-
on (POR or wakeup from
Standby)
V
DD
= 1.7 V, T
A
= 105 °C,
I
RUSH
= 171 mA for 31 µs
--5.4µC
1. The product behavior is guaranteed by design down to the minimum V
POR/PDR
value.
2. Guaranteed by design, not tested in production.
3. The reset timing is measured from the power-on (POR reset or wakeup from V
BAT
) to the instant when first
instruction is fetched by the user application code.
Table 19. Embedded reset and power control block characteristics (continued)
Symbol Parameter Conditions Min Typ Max Unit
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.