Datasheet

Electrical characteristics STM32F105xx, STM32F107xx
64/108 DocID15274 Rev 10
5.3.16 Communications interfaces
I
2
C interface characteristics
Unless otherwise specified, the parameters given in Table 41 are derived from tests
performed under the ambient temperature, f
PCLK1
frequency and V
DD
supply voltage
conditions summarized in Table 9.
The STM32F105xx and STM32F107xx
I
2
C interface meets the requirements of the
standard I
2
C communication protocol with the following restrictions: the I/O pins SDA and
SCL are mapped to are not “true” open-drain. When configured as open-drain, the PMOS
connected between the I/O pin and V
DD
is disabled, but is still present.
The I
2
C characteristics are described in Table 41. Refer also to Section 5.3.12: I/O current
injection characteristics
for more details on the input/output alternate function characteristics
(SDA and SCL)
.
Table 41. I
2
C characteristics
Symbol Parameter
Standard mode I
2
C
(1)
1.
Guaranteed by design, not tested in production.
Fast mode I
2
C
(1)(2)
2. f
PCLK1
must be at least 2 MHz to achieve standard mode I
2
C frequencies. It must be at least 4 MHz to
achieve the fast mode I
2
C frequencies and it must be a mulitple of 10 MHz in order to reach I
2
C fast mode
maximum clock 400 kHz.
Unit
Min Max Min Max
t
w(SCLL)
SCL clock low time 4.7 - 1.3 -
µs
t
w(SCLH)
SCL clock high time 4.0 - 0.6 -
t
su(SDA)
SDA setup time 250 - 100 -
ns
t
h(SDA)
SDA data hold time 0
(3)
3.
The maximum hold time of the Start condition has only to be met if the interface does not stretch the low
period of SCL signal.
-0
(4)
4.
The device must internally provide a hold time of at least 300ns for the SDA signal in order to bridge the
undefined region of the falling edge of SCL.
900
(3)
t
r(SDA)
t
r(SCL)
SDA and SCL rise time - 1000 20 + 0.1C
b
300
t
f(SDA)
t
f(SCL)
SDA and SCL fall time - 300 - 300
t
h(STA)
Start condition hold time 4.0 - 0.6 -
µs
t
su(STA)
Repeated Start condition
setup time
4.7 - 0.6 -
t
su(STO)
Stop condition setup time 4.0 - 0.6 - μs
t
w(STO:STA)
Stop to Start condition time
(bus free)
4.7 - 1.3 - μs
C
b
Capacitive load for each bus
line
- 400 - 400 pF
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.