LD29150 1.5 A, very low drop voltage regulators Datasheet - production data Description The LD29150 is a high current, high accuracy, low-dropout voltage regulator series. These regulators feature 400 mV dropout voltage and very low ground current. Designed for high current loads, these devices are also used in lower current, extremely low dropout-critical systems, where their tiny dropout voltage and ground current values are important attributes.
Contents LD29150 Contents 1 Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 Typical application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 5 Electrical characteristics . . .
LD29150 1 Diagram Diagram Figure 1. Schematic diagram for adjustable version Figure 2. Schematic diagram for fixed version * Only for version with inhibit function.
Pin configuration 2 LD29150 Pin configuration Figure 3. Pin connections (top view) PPAK DPAK * Not connected for fixed version.
LD29150 3 Typical application Typical application Figure 4. Application circuit V O = V REF (1 + R 1/R 2 ) * Only for version with inhibit function.
Maximum ratings 4 LD29150 Maximum ratings Table 2. Absolute maximum ratings Symbol Parameter Value Unit (1) VI DC input voltage VO DC output voltage -0.3 to 20 V Inhibit input voltage -0.3 to 20 V VINH 30 V IO Output current Internally limited mA PD Power dissipation Internally limited mW TSTG Storage temperature range -55 to 150 °C TOP Operating junction temperature range -40 to 125 °C 1. Above 14 V the device is automatically in shut-down.
LD29150 Electrical characteristics 5 Electrical characteristics IO = 10 mA, TJ = 25 °C, VI = 3.8 V, VINH = 2 V (Note 3), CI = 330 nF, CO = 10 µF, unless otherwise specified. Table 4. Electrical characteristics of LD29150#18 Symbol Parameter Test conditions Min. Typ. Max. 1.782 1.8 1.818 Unit VO Output voltage IO = 10 mA to 1.5 A, VI = 3 to 7.3 V TJ = - 40 to 125 °C VO Load regulation IO = 10 mA to 1.5 A 0.2 1.0 % VO Line regulation VI = 3 to 13 V 0.06 0.
Electrical characteristics LD29150 IO = 10 mA, TJ = 25 °C, VI = 4.5 V, VINH = 2 V (Note 3), CI = 330 nF, CO = 10 µF, unless otherwise specified. Table 5. Electrical characteristics of LD29150#25 Symbol Parameter Test conditions Min. Typ. Max. 2.475 2.5 2.525 Unit VO Output voltage IO = 10 mA to 1.5 A, VI = 3.5 to 8 V TJ = - 40 to 125 °C VO Load regulation IO = 10 mA to 1.5 A 0.2 1.0 % VO Line regulation VI = 3.5 to 13 V 0.06 0.
LD29150 Electrical characteristics IO = 10 mA, TJ = 25 °C, VI = 5.3 V, VINH = 2 V (Note 3), CI = 330 nF, CO = 10 µF, unless otherwise specified. Table 6. Electrical characteristics of LD29150#33 Symbol Parameter Test conditions Min. Typ. Max. 3.267 3.3 3.333 Unit VO Output voltage IO = 10 mA to 1.5 A, VI = 4.3 to 8.8 V TJ = - 40 to 125 °C VO Load regulation IO = 10 mA to 1.5 A 0.2 1.0 % VO Line regulation VI = 4.3 to 13 V 0.06 0.
Electrical characteristics LD29150 IO = 10 mA, TJ = 25 °C, VI = 7 V, VINH = 2 V (Note 3), CI = 330 nF, CO = 10 µF, unless otherwise specified. Table 7. Electrical characteristics of LD29150#50 Symbol Parameter Test conditions Min. Typ. Max. 4.95 5 5.05 Unit VO Output voltage IO = 10 mA to 1.5 A, VI = 6 to 10.5 V TJ = - 40 to 125 °C VO Load regulation IO = 10 mA to 1.5 A 0.2 1.0 % VO Line regulation VI = 6 to 13 V 0.06 0.
LD29150 Electrical characteristics IO = 10 mA, TJ = 25 °C, VI = 3.23 V, VINH = 2 V (Note 3), CI = 330 nF, CO = 10 µF adjust pin tied to output pin. Table 8. Electrical characteristics of LD29150#ADJ Symbol Parameter Test conditions Min. Typ. Max. Unit Minimum operating input voltage IO = 10 mA to 1.5 A, TJ = - 40 to 125 °C VO Load regulation IO = 10 mA to 1.5 A 0.2 1.0 % VO Line regulation VI = 2.5 V to 13 V, IO = 10 mA 0.06 0.5 % VREF Reference voltage IO = 10 mA to 1.
Typical characteristics 6 LD29150 Typical characteristics Figure 5. Output voltage vs. temperature Figure 6. Reference voltage vs. temperature Figure 7. Dropout voltage vs. temperature Figure 8. Dropout voltage vs. output current Figure 9. Quiescent current vs. output current Figure 10. Quiescent current vs. output current (VI = 13 V) (VI = 4.
LD29150 Typical characteristics Figure 11. Quiescent current vs. supply voltage Figure 12. Quiescent current vs. temperature (IO = 10 mA) Figure 13. Quiescent current vs. temperature (IO = 1.5 A) Figure 14. Short circuit current vs. temperature Figure 15. Adjust pin current vs. temperature Figure 16. Supply voltage rejection vs.
Typical characteristics LD29150 Figure 17. Output voltage vs. input voltage Figure 18. Stability vs. CO Figure 19. Line transient Figure 20. Load transient VI=3.5 to 5.5V, IO=10mA, VO=2.5V, CO=10µF VI=5V, IO=10mA to 1.5A, VO=2.5V, CO=10µF Figure 21. Start-up time 10 mA CO=10µF, IO=10mA, VINH=2V, VO=5V, VI=7V 14/23 Figure 22. Start-up time 1.5 A CO=10µF, IO=1.
LD29150 7 Package information Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. 7.1 DPAK package information Table 9. DPAK mechanical data mm Dim. Min. Typ. Max. A 2.20 2.40 A1 0.90 1.10 A2 0.03 0.23 b 0.64 0.90 b4 5.20 5.40 c 0.
Package information LD29150 Figure 23.
LD29150 Package information Figure 24. DPAK footprint (a) Footprint_REV_K a.
Package information 7.2 LD29150 PPAK package information Table 10. PPAK mechanical data mm Dim. Min. Max. A 2.2 2.4 A1 0.9 1.1 A2 0.03 0.23 B 0.4 0.6 B2 5.2 5.4 C 0.45 0.6 C2 0.48 0.6 D 6 6.2 D1 E 5.1 6.4 E1 6.6 4.7 e 1.27 G 4.9 5.25 G1 2.38 2.7 H 9.35 10.1 L2 0.8 L4 0.6 L5 1 L6 1 1 2.8 R V2 18/23 Typ. 0.
LD29150 Package information Figure 25.
Packaging information LD29150 8 Packaging information 8.1 PPAK and DPAK packaging information Table 11. PPAK and DPAK tape and reel mechanical data Tape Reel mm mm Dim. Dim. Min. Max. A0 6.8 7 A B0 10.4 10.6 B 1.5 12.1 C 12.8 1.6 D 20.2 G 16.4 50 B1 20/23 Min. Max. 330 13.2 D 1.5 D1 1.5 E 1.65 1.85 N F 7.4 7.6 T K0 2.55 2.75 P0 3.9 4.1 Base qty. 2500 P1 7.9 8.1 Bulk qty. 2500 P2 1.9 2.1 R 40 T 0.25 0.35 W 15.7 16.3 DocID9614 Rev 20 18.
LD29150 Packaging information Figure 26. Tape for PPAK and DPAK 10 pitches cumulative tolerance on tape +/- 0.2 mm T P0 Top cover tape P2 D E F B1 W K0 B0 For machine ref. only including draft and radii concentric around B0 A0 P1 D1 User direction of feed R Bending radius User direction of feed AM08852v1 Figure 27. Reel for PPAK and DPAK T REEL DIMENSIONS 40mm min. Access hole At slot location B D C N A Full radius Tape slot in core for tape start 25 mm min.
Revision history 9 LD29150 Revision history Table 12. Document revision history 22/23 Date Revision Changes 17-Jun-2004 5 Add figures 20 and 21, PPAK, TO-220 and TO-220FP mechanical data updated. 19-Jul-2004 6 Remove Package TO-220FP4. 08-Nov-2004 7 Mistake Figure 7. 21-Mar-2005 8 Add VO and VINH on Table 2. 21-Oct-2005 9 Order Codes Has Been Updated. 17-Oct-2006 10 Add new package P²PAK. 13-Nov-2006 11 Add row TSHDN on tables of the electrical characteristics.
LD29150 IMPORTANT NOTICE – PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement.