RZ4-2ARC SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030 www.SSVWorks.com I Phone: 818-991 -1778 I Fax: 866-293-6751 Polaris RZR XP Turbo S 2-Speaker Kit WARRANTY INFORMATION: All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or workmanship. All SSVWorks Electronics are covered by a limited 1 year warranty against defects in material or workmanship. All Kicker Speakers are covered by a limited 1 year warranty against defects in material or workmanship.
PANELS AND DASH DISASSEMBLY A. Remove driver seat by releasing the handle behind each seat, push forward slightly while lifting up B. Disconect the negative battery cable from the battery. C. Remove all of the center console push pins and T-30 Tone screws. For 4-seat models, disconnect the harness attached to the 12v accessory socket. D. Remove hood by turning locking pins and lifting up. E. Unscrew the (4) T40 tone screws (showing driver side only in image) and extract the (2) push pins from the dash.
RUNNING WIRING AND CABLES F. Unwrap the tape and pull the rubber wire grommet out of the firewall. D. Feed the connector end of the Amp power wire through the center console to the other side of the firewall (G1). Then feed the power wire through the grommet hole (G2) and through the rubber grommet with the rest of the vehicle's wiring and cables (G3). Do the same for the B-H 1151 rear speaker harness. The purpose of this harness is to add rear speakers - sold separately. · H.
AMP TRAY INSTALLATION A. Remove the (2) 10mm bolts circled in pink B. Place the amp tray base bracket at the location of the (2) removed factory 10mm bolts. Re-fasten the bolts through both the amp tray base bracket and factory plate to secure to the chassis. C. Remove the (2) 10mm bolts circled in pink D. Place the amp tray into the mounting location by lining up the amp plate screw holes to the factory holes on the chassis. E.
AMP TRAY INSTALLATION G. With the correct location marked, uninstall the amp tray and use a 13/64" drill bit to drill your pilot hole. With your pilot hole drilled, reinstall the amp tray. Use the selftapping screw in the drilled hole location. H. Connect the amplifier "Front Input" to the Ride Command "Audio Amp 1" factory harness. Connect the amplifier "Rear Input" for rear speakers to "Audio Amp 2" factory harness.
Polaris RZR XP Turbo S Kicker 6.5" Speaker Front Kick Panels SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030 www.SSVworks.com I Phone: 818-991-1778 I Fax: 866-293-6751 WARRANTY INFORMATION: All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty against defects in material or workmanship.
A. Using the utility knife or another cutting tool cut off the two plastic factory nubs in the foot well , cut these as smooth as you can to the panel. NOTE: If pod does not come pre-installed with speaker, do not use provided paper templates. Use the pod mounting holes as your drill template. Hold the pod in position and mark the drill holes through the empty pod using a scribe tool. All pilot holes will be drilled from the inside footwell. B.
__ II C. Drill a pilot hole at the places just marked with a 1/8" drill bit. Then follow up by using a 1/4" drill bit in the lower pilot hole (for mounting the pod) and a 1/2" drill bit in the upper pilot hole (for speaker cable). D. Cut out the OUTSIDE template (Driver/Passenger) along the cut line. Position the template on the outside footwell. Make su re the bottom of the template lines up along the bottom edge and tab of the factory panel as shown in figure D1-D3.
E. Drill a pilot hole at the places just marked with a 1/8" drill bit. Then follow up by using a 1/4" drill bit for both pilot holes (for mounting the pod). F. Route the speaker cable attached to the pod through the inside footwell 1/2" hole made in Step D. G. Position the speaker pod in place and line up with drilled mounting holes H. With the provided M6 screws and washers, loosely mount the pod through the 3 holes previously drilled.
RZ3-F65 2017 Polaris RZR Kick Pod, Cut Template Driver Outside Template ! -~ · Drill Point I -~ 1 ' Drill Point Cut along parimeter ' 11
~ ~ Drill Point 2017 Polaris RZR Kick Pod, Cut Template Passenger Inside Templat~ Cut along parimeter i - ~ ' Drill Point '
2017 Polaris RZR Kick Pod, Cut Template Passenger Outside Template I ~ ) -Drill Point 1 Drill Point ' Cut along parimeter ' 15
~ fa) Drill Point 2017 Polaris RZR Kick Pod, Cut Template Driver Inside Template Cut along parimeter I - ~ D r i l l Point ' '
I CONNECTING POWER & GROUND CABLE TO BATTERY Power Wire Battery Tenninal Cable Break off tab • A1. Remove the bottom cover of the fuse holder by extracting the 2 screws. Break off the right and left side tabs on the bottom cover. A2. Extract both fuse holder screws. _ ____ _ .;:..._ ___, II A3. Attach both the Power Wire and Battery Tenninal Cable to the fuse holder. Reattach the bottom cover. II B. Unscrew the factory nut on the negative battery tenninal.
LOOKING FOR MORE SOUND? TRYSSVWORKS CAGE MOUNT 6.5" SPEAKER PODS! SSV Works custom molded Cage Mount Pods are designed for 6.5" speakers and can be used when you need more sound in your Side by Side. Unlike wakeboard towers, these mini pods are designed to provide sound to the passengers without blocking visibility. They are 100% fiberglass for the best sound quality and bass response.