RZ3-1KRC RZR XP1000 & 2015+ RZR900 with Ride Command SSV Works Subwoofer Audio Kit pg 2 pg 6 Disassembly, Wire and Amplifier Plate Installation Glovebox Subwoofer Installation
RZR XP1000 & 2015+ RZR900 Amp Tray and Wiring Installation WARRANTY INFORMATION: All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty against defects in material or workmanship. All Kicker Speakers are covered by a limited 1 year warranty against defects in material or workmanship.
PANELS AND DASH DISASSEMBLY A A. Remove all seats by releasing the handle behind each seat, push forward slightly while lifting up. B B. Disconect the negative battery cable from the battery. C C. Remove hood by turning locking pins and lifting up. D D D. Remove center dash by unscrewing the (2) T-40 Torx screws and push center dash forward to unclip. E E. Disconnect all harness connectors attached to the center dash panel. F F. Un-pin and pull to remove the passenger side safely handle.
PANELS AND DASH DISASSEMBLY G1 G2 G3 G. Remove the factory dash pocket by first extracting the 10mm bolt on the dash frame (G1). Then pull out the dash pocket with bracket attached (G2) - NOTE this bracket will no longer be used for any part of this installation. Save this screw as it will be use later during the amp plate installation. Extract (2) screws securing the sub dash (G3). Unsnap and remove. H H H H. Remove all of the center console push pins and T-40 Torx screws.
RUNNING AMP POWER CABLE AND REAR SPEAKER WIRE A1 A2 A3 A. Starting from under the hood compartment, feed the connector of the power wire through the grommet into the dash cavity. In order to connect to the amplifier in a later step, pull about 18” of the amp power wire into the dash cavity (A1). Route the additional length of the (ring terminal end) power/ ground wire down the exterior of the firewall along the factory wiring (A2).
RZR Turbo S & RZR XP1000 2014+ Glove Box Subwoofer Enclosure WARRANTY INFORMATION: All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty against defects in material or workmanship. All SSV Works Speakers are covered by a limited 1 year warranty against defects in material or workmanship.
B A A. Using (4) 8mm screws and washers, attach Bracket “B” to the enclosure. C B. Install door latch onto enclosure with the provided (2) 8mm screws and washers. C C. Install left and right door hinge brackets using (2) 8mm screws and washers for each side. D D. Install lower mounting bracket onto enclosure with the provided (2) 8mm screws and washers. E E. With the dash removed, extract the (2) 10mm bolts retaining the glovebox and remove the glovebox.
F F F F. Lift the enclosure into place. Using the factory glove box mounting hardware, fasten the enclosure into place. G H G. Place Bracket “A” into place towards the firewall, and fasten it into place with the (4) 8mm socket head screws and washers provided with the kit. H. Fasten the provided #14 screw to secure the enclosure lower mounting bracket. I I. Attach the factory glovebox door. J J. Connect the sub enclosure to the 500.1 amplifier front output.
CONNECTING POWER & GROUND CABLE TO BATTERY Power Wire Break off tab Battery Terminal Cable Break off tab A1 A1. Remove the bottom cover of the fuse holder by extracting the 2 screws. Break off the right and left side tabs on the bottom cover. A2 A2. Extract both fuse holder screws. B B. Unscrew the factory nut on the negative battery terminal. Install the 2 ground cables to the screw on the ground battery terminal. Re-install the factory nut. D D.
