User Guide EiEiV IIICIRKS MRB3 @) TRACK @ [Moo~ ~ MRB3 Bluetooth Media Controller SAFETY INFORMATION Do not attempt to disassemble or repair the MRB3 yourself. Please call SSV Works for technical assistance or repair information. Changes or modifications to the MRB3 not authorized by SSV Works will void the warranty. A ~ SSV Works recommends disconnecting the negative battery terminal before beginning any installation.
AMPLIFIER WIRING DIAGRAM Power connector 12v+ Y e l l o w ~ Black a Rear left(+) Green Rear right(+) Purple Yellow ........
BUTTON LOCATIONS AND FUNCTIONS e -1---- 1. Play/Pause Power On/Off Mute 2. Volume Up/Down @ VOL - - - - - - ~ TRACK @ 9~7 ~ ~ • • • • ---1--1--- 3. Mode 4. Track Forward/Back Station Forward/Back Menu Settings Up/Down 5. LCD Dispiay GENERAL OPERATIONS Power On/Off: Press ►II to power on. Press and hold ►II to power off. Volume: Press the VOL(+) or(·) button to increase or decrease the volume. Mute On/Off: Press ►II briefly to mute the sound. Press. ►II again to un-mute the sound.
RADIO FUNCTIONS Selecting FM/AM Band: Press MODE until the FM or AM band shows on the display. Automatic Station Search: Press A or stops when a station is found. ~ to start automatic station search. The search Manual Station Search: Press and hold A or ~ until M - SEEK. Press the A or ~ briefly to change the frequency until the desired frequency is set. Change to Automatic search (A - SEEK) mode after a station is found. BLUETOOTH AUDIO STREAMING 1.
RKR-2K Can-Am Ryker 2-Speaker Audio Kit SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030 www.SSVworks.com I Phone: 818-991-1778 I Fax: 866-293 -6751 WARRANTY INFORMATION: All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or workmanship. All SSVWorks Electronics are covered by a limited 1 year warranty against defects in material or workmanship. All Kicker Speakers are covered by a limited 1 year warranty against defects in material or workmanship.
A. Compress the locking tabs to the hood and slide the hood down simultaneously to release the hood and remove. B. Use a 10mm socket to disconnect the negative battery terminal. C. Open the front storage compartment, remove the (4) push pins and (2) T20 Tone screws. D. Slide back the fuel door. Remove the (4) push pins that are now exposed. E. Pull the driver and passenger side panels off the Ryker. F. Using a panel tool, release the clips for the trim panel from the storage compartment.
G. Once the fairing panel has been released, lift the front storage compartment and disconnect the USB charging port. Set the compartment aside for future steps. I. Align the RKR-2K over the mounting bases. Fasten the RKR-2K to the mounting brackets with the provided (4) M6xl.Ox12mm torx screws and (4) M6 washers using a T30 Torx driver. K. Place the USB charging port into the front of the MRB3 mounting plate and refasten the nut. H.
M. Remove the MRB3 brain assembly from the storage container and drill a pilot hole with a 1/8" drill bit at each marked point. Open up each pilot hole with a 5/ 16" drill bit. N. To route the harness from the RKR-2K to the MRB3 brain, pull the harnesses from the RKR-2K back around the upperfairing panel and to the front of the fairing panel. We recommend turning your handlebars to the right to allow for the most clearance for routing the cables. 0.
S. Connect the factory USB port to the power ground. Reference the back of the USB port to identify which terminal is power or ground. T. Connect the antenna. U. Connect the MRB3 front speaker output to the RKR-2K input. V. Align the arrows on the wire control panel with the arrow on the MRB3 controller connector and connect. W. Connect the MRB3 power connector to the RKR-2K power output. X. Place the now connected MRB3 brain in its mounting position over the holes drilled in Step L.
Y. From the exterior of the storage compartment, place (2) push pins on each side to mount the MRB3 in place. Z. Place the storage compartment back into its cavity. A1. Hold the center cover onto the front of the RKR-2K, faste·n the (2) M3 machine screws into the system to retain the cover. B1. Support the top of the center cover of the system and fasten the (2) #4 coarse threaded screws to into the unit to complete cover installation. Test the system prior to reassembly of the vehicle.
