RZ3-5KRC RZR XP1000 & 2015+ RZR900 with Ride Command SSV Works 5 Speaker Audio Kit pg 2 pg 9 pg 13 pg 25 Disassembly, Wire and Amplifier Plate Installation Glovebox Subwoofer Installation Kick Panel Speakers Installation Cage Mount Speakers Installation
RZR XP1000 & 2015+ RZR900 Amp Tray and Wiring Installation SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030 www.SSVworks.com | Phone: 818-991-1778 | Fax: 866-293-6751 WARRANTY INFORMATION: All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty against defects in material or workmanship.
PANELS AND DASH DISASSEMBLY A A. Remove driver seat by releasing the handle behind each seat, push forward slightly while lifting up B B. Disconect the negative battery cable from the battery. C C C C. Remove all of the center console push pins and T-30 Torx screws. For 4-seat models, disconnect the harness attached to the 12v accessory socket. D D. Remove hood by turning locking pins and lifting up. E E.
RUNNING WIRING AND CABLES F F. Unwrap the tape and pull the rubber wire grommet out of the firewall. G1 G2 G3 D. Feed the connector end of the Amp power wire through the center console to the other side of the firewall (G1). Then feed the power wire through the grommet hole (G2) and through the rubber grommet with the rest of the vehicle’s wiring and cables (G3). Do the same for the B-H1151 rear speaker harness. The purpose of this harness is to add rear speakers - sold separately.
AMP TRAY INSTALLATION A A. Remove the (2) 10mm bolts circled in pink B B. Place the amp tray base bracket at the location of the (2) removed factory 10mm bolts. Re-fasten the bolts through both the amp tray base bracket and factory plate to secure to the chassis. C C. Remove the (2) 10mm bolts circled in pink D D. Place the amp tray into the mounting location by lining up the amp plate screw holes to the factory holes on the chassis. E E.
AMP TRAY INSTALLATION G G. With the correct location marked, uninstall the amp tray and use a 13/64” drill bit to drill your pilot hole. With your pilot hole drilled, reinstall the amp tray. Use the selftapping screw in the drilled hole location. H H. Connect the amplifier “Front Input” to the Ride Command “Audio Amp 1” factory harness. Connect the amplifier “Rear Input” for rear speakers to “Audio Amp 2” factory harness. THIS CONCLUDES THE DISASSEMBLY AND RUNNING OF THE POWER AND SPEAKER WIRE.
RZR XP1000 & 2015+ RZR900 Kicker 10” Glove Box Subwoofer Enclosure SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030 www.SSVworks.com | Phone: 818-991-1778 | Fax: 866-293-6751 WARRANTY INFORMATION: All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty against defects in material or workmanship.
B A A. Remove the ten T40 Torx bolts that secure the 2 piece fender. Note: there is one screw inside the fender well. Remove the two additional screws from the striker plate, slide fender up the cage rail and secure C B. Remove the two 10mm bolts that secure factory glove box and remove the factory glove box C C. Lift the enclosure into place and align the top channel in the grab handle bar.
G G. For 2015-up model year vehicles, install the supplied bracket using the short screws provided and adjust forward or back so glove box latch closes tight H H. For 2014 model year vehicles remove the factory glove box door latch. Mount the latch to the supplied bracket and secure to the enclosure using the short screws provided I I. Route the speaker wire away from any moving parts and any sharp metal, then connect to the amplifier. J J.
RZR XP1000 & 2015+ RZR900 Kicker 6.5” Speaker Front Kick Panels SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030 www.SSVworks.com | Phone: 818-991-1778 | Fax: 866-293-6751 WARRANTY INFORMATION: All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty against defects in material or workmanship.
A A. Using the utility knife or another cutting tool cut off the two plastic factory nubs in the foot well, cut these as smooth as you can to the panel. NOTE: If pod does not come pre-installed with speaker, do not use provided paper templates. Use the pod mounting holes as your drill template. Hold the pod in position and mark the drill holes through the empty pod using a scribe tool. All pilot holes will be drilled from the inside footwell. B1 B2 B3 B4 B.
C1 C2 C. Drill a pilot hole at the places just marked with a 1/8” drill bit. Then follow up by using a 1/4” drill bit in the lower pilot hole (for mounting the pod) and a 1/2” drill bit in the upper pilot hole (for speaker cable). D1 E1 D4 D2 D3 D5 D. Cut out the OUTSIDE template (Driver/Passenger) along the cut line. Position the template on the outside footwell. Make sure the bottom of the template lines up along the bottom edge and tab of the factory panel as shown in figure D1-D3.
E1 E2 E. Drill a pilot hole at the places just marked with a 1/8” drill bit. Then follow up by using a 1/4” drill bit for both pilot holes (for mounting the pod). F G F. Route the speaker cable attached to the pod through the inside footwell 1/2” hole made in Step D. G. Position the speaker pod in place and line up with drilled mounting holes H H H. With the provided M6 screws and washers, loosely mount the pod through the 3 holes previously drilled.
RZ3-F65 2017 Polaris RZR Kick Pod, Cut Template Driver Outside Template Drill Point Drill Point Cut along parimeter 17
Drill Point RZ3-F65 2017 Polaris RZR Kick Pod, Cut Template Passenger Inside Template Cut along parimeter Drill Point 19
RZ3-F65 2017 Polaris RZR Kick Pod, Cut Template Passenger Outside Template Drill Point Drill Point Cut along parimeter 21
RZ3-F65 2017 Polaris RZR Kick Pod, Cut Template Driver Inside Template Cut along parimeter Drill Point Drill Point 23
Universal Cage Mount Kicker 6.5” Speaker Enclosures SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030 www.SSVworks.com | Phone: 818-991-1778 | Fax: 866-293-6751 WARRANTY INFORMATION: All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty against defects in material or workmanship.
A A. Find the best orientation for the speaker on your bar and screw in the Set Screws in the OPPOSITE holes of where the clamp will install into. C B B. Loosely install the clamp base to the cage mount pod with the two (2) M6 hex head bolts and washers, place the cage mount pod in the desired mounting location on the vehicle. Once the ring adapter is in the desired position, tighten the two (2) bolts using a 8mm open wrench. C C C.
E D D. Position the speaker to your liking and tighen the hex head bolts by hand with a 8mm wrench. E. From the rear of the center console, route the B-H1150 harness up to each speaker pod and connect. F F. Route the speaker wire away from any moving parts and any sharp metal, then connect to the amplifier G G.
CONNECTING POWER & GROUND CABLE TO BATTERY Power Wire Break off tab Battery Terminal Cable Break off tab A1 A1. Remove the bottom cover of the fuse holder by extracting the 2 screws. Break off the right and left side tabs on the bottom cover. A2 A2. Extract both fuse holder screws. B B. Unscrew the factory nut on the negative battery terminal. Install the 2 ground cables to the screw on the ground battery terminal. Re-install the factory nut. D D.