RZ4-3KRC RZR XP Turbo S with Ride Command SSV Works 3 Speaker Audio Kit pg2 Disassembly, Wire and Amplifier Plate Installation Glovebox Subwoofer Installation pg13 Kick Panel Speakers Installation
RZR XP1000 & 2015+ RZR900 Amp Tray and Wiring Installation SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030 www.SSVworks.com I Phone: 818-991-1778 I Fax: 866-293-6751 WARRANTY INFORMATION: All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty against defects in material or workmanship.
PANELS AND DASH DISASSEMBLY A. Remove driver seat by releasing the handle behind each seat, push forward slightly while lifting up 8. Disconect the negative battery cable from the battery. C. Remove all of the center console push pins and T-30 Torx screws. For 4-seat models, disconnect the harness attached to the 12v accessory socket D. Remove hood by turning locking pins and lifting up. E. Unscrew the (4) T40 torx screws (showing driver side only in image) and extract the (2) push pins from the dash.
RUNNING WIRING AND CABLES F. Extract the (4) T40 surrounding the ride command system and (2) push pins found in the dash pocket. *for non-ride command vehicles, less hardware may need to be removed for this step. Upclip the dash surrounding the glovebox. Once unclipped, gently pull the dash forward and remove the upper dash pocket. G. Unwrap the tape and pull the rubber wire grommet out of the firewall. H. Extract the (1) T40 torx that secures the lower dash pocket. I.
RUNNING WIRING AND CABLES his following steps are needed to ensure clearance for the sub enclosure and allow proper performance II C. Grind flat across to the locking tap shown in fig C. *Do not grind the tab. A. Start by removing the four (4) 10mm bolts securing the Dynamix brain tray. C. Grind flat across to the locking tap shown in fig C. * Do not grind the tab. D. Grind a notch for the cables to rest in. Drill two (2) holes for a zip tie on each side of the lower corners of the square logo. B.
AMP TRAY INSTALLATION E. Run a zip tie through the connector housing as shown in figure E. F. Snap the connector housing back into place over the connector. G. Bend harness towards zip tie and close the tie. H. Cinch down zip tie as show in figure (H). Put the Dynamix brain tray back in place but DO NOT REPLACE THE BOLTS. I. Place the amp tray base bracket at the location of the (2) removed factory 10mm bolts.
AMP TRAY INSTALLATION K. Secure the amp tray by using the two (2) factory bolts at the top, and two (2) M6 bolts at the bottom mounting locations. L. Using a scribe or punch, mark the location of the needed pilot hole on the passenger side of the tray. M. With the correct location marked, uninstall the amp tray and use a 13/64" drill bit to drill your pilot hole. With your pilot hole drilled, reinstall the amp tray. Use the selftapping screw in the drilled hole location. N.
RZR XP1000 & 2015+ RZR900 Kicker 10" Glove Box Subwoofer Enclosure SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030 www.SSVworks.com I Phone: 818-991-1778 I Fax: 866-293-6751 WARRANTY INFORMATION: All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty against defects in material or workmanship.
A. Remove the two 10mm bolts that secure factory glove box and remove the factory glove box B. Lift the enclosure into place and align the top channel in the grab handle bar. towards firewall C. Lift the enclosure into place and align the top channel in the grab handle bar, while holding the enclosure in place, loosely attached the flat brackets to the top of the enclosure using the 8mm socket head screws provided. D.
F. For 2015-up model year vehicles, install the supplied bracket using the short screws provided and adjust forward or back so glove box latch closes tight G. For 2014 model year vehicles remove the factory glove box door latch. Mount the latch to the supplied bracket and secure to the enclosure using the short screws provided H. Route the speaker wire away from any moving parts and any sharp metal, then connect to the amplifier. I.
RZR XP1000 & 2015+ RZR900 Kicker 6.5" Speaker Front Kick Panels SSVWORKS, 201 N. Rice Ave Unit A, Oxnard, CA93030 www.SSVwor~.com I Phone: 818-991-1778 I Fax: 866-293-6751 WARRANTY INFORMATION: All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or workmanship. All SSVWorks Electronics are covered by a limited 1 year warranty against defects in material or workmanship.
A. Using the utility knife or another cutting tool cut off the two plastic factory nubs in the foot well, cut these as smooth as you can to the panel. NOTE: If pod does not come pre-installed with speaker, do not use provided paper templates. Use the pod mounting holes as your drill template. Hold the pod in position and mark the drill holes through the empty pod using a scribe tool. All pilot holes will be drilled from the inside footwell. 8.
,., \,~ ' \' \ /4. / _,!J~ 9 \ ~~- 1,· ---•.......______ '\ ·. i C. Drill a pilot hole at the places just marked with a 1/8" drill bit. Then follow up by using a 1/4" drill bit in the lower pilot hole (for mounting the pod) and a 1/2" drill bit in the upper pilot hole (for speaker cable). D. Cut out the OUTSIDE template (Driver/Passenger) along the cut line. Position the template on the outside footwell.
E. Drill a pilot hole at the places just marked with a 1/8" drill bit. Then follow up by using a 1/ 4" drill bit for both pilot holes (for mounting the pod). F. Route the speaker cable attached to the pod through the inside footwell 1/2" hole made in Step D. G. Position the speaker pod in place and line up with drilled mounting holes H. With the provided M6 screws and washers, loosely mount the pod through the 3 holes previously drilled.
RZ3-F65 2017 Polaris RZR Kick Pod, Cut Template Driver Outside Template ! -~□ril Point I -~ ' 1 Drill Point Cut along parimeter ' 17
~ ~ - Drill Point 2017 Polaris RZR Kick Pod, Cut Template Passenger Inside Template Cut along parimeter I - ~ ' Drill Point '
2017 Polaris RZR Kick Pod, Cut Template Passenger Outside Template I ~ - Drill Point 1 I ~ - Drill Point ' Cut along parimeter ' 21
('t) N m )U Drill Point 2017 Polaris RZR Kick Pod, Cut Template Driver Inside Template Cut along parimeter I -4 - ~ Drill Point ' '
- --- -----~--------~-~ - - ~ - - - - - - - - CONNECTING POWER & GROUND CABLE TO BATTERY Power Wire 1 Battery Terminal Cable .. Break offtab A1. Remove the bottom cover of the fuse holder by extracting the 2 screws. Break off the right and left side tabs on the bottom cover. A2. Extract both fuse holder screws. A3. Attach both the Power Wire and Battery Terminal Cable to the fuse holder. Reattach the bottom cover. B. Unscrew the factory nut on the negative battery terminal.
