Use and Care Guide

10-08 tk
©2008 Schneider Electric. All rights reserved.
Schneider Electric - North American Operating Division
1415 S. Roselle Road
Palatine, IL 60067
Tel: [phone]
Fax: [phone]
Document Number 9013HO0801
Reverse action pressure switches
Schneider Electric’s reverse action pressure
switches t the needs of your specialty
pumping applications. These reverse action
pressure switches are available with normally
open (N.O.) contacts, thus making them the
perfect solution for applications such as:
Pump-out application
Applications designed to empty a tank utilize
these reverse action pressure switches to start
a pump until the pressure/uid level is reduced
to the desired point.
Pump shut down application
The 9013FRG reverse action pressure switches
can be wired in series with the FSG standard
action normally closed (N.C.) pressure switches
to automatically shut off pumps in case of
emergency such as power loss or when a
pipe bursts.
Low level alarm application
The 9013FRG reverse action pressure switch
can be set to trigger an alarm based on the
low pressure conditions.
Manual on/off switch
The 9013 series offers an optional on/off lever
for the pressure switch. This allows you to
manually turn on and off your pump system for
extended periods of time such as when you are
going to be away or have remote locations not
regularly in use.
Automatic low pressure/water cut-off
If system pressure is lost for any reason, a low
water condition for example, the automatic
low pressure/water cut-off feature will open
the contacts, turning off the pump. The low
water cut off functions normally and cycles the
pump per your typical demands, however, if
the system pressure is lost for any reason, the
switch contacts open, turning off the pump.
Optional features available for the 9013 reverse
action product line
Many optional features are available to increase the functionality
and performance of your Schneider Electric pressure switches.
See the table below to identify the feature which you may need for
your application.
* Nylon pulsation plug can be eld installed on types having 1/4" NPSF internal
connector. Part number1530S6G1 is one bag of 50 plugs.
Explanation of a part number (example: 9013FRG12J51)***
9013 + FS + G + 12 + J51 +
Class Type Enclosure Fluid Pressure Forms
Connection Codes
Type R = Reverse action
Enclosure G = NEMA 1
Fluid
Connection
2 = 1/4" NPSF internal
3 = 3/8" NPSF internal
8 = 1/4" are
9 = 1/4" NPT external
Others available
Pressure
Codes
J19 = 22-16 PSI
J22 = 22-12 PSI
J23 = 40-20 PSI
J32 = 80-60 PSI
J35 = 50-30 PSI
J51 = 100-80 PSI
J99 = Specify range
Others available
Poles Various numerials signify a 1-pole or a 2-pole unit at different pressure
ranges. May or may not require a numerial in combination with the
uid connection.
Forms H = 1 N.O. and 1 N.C.
M3 = Momentary manual cut-in lever
M5 = Maintained manual cut-in lever
Q8 = Plastic ange
P = Pulsation plug
T = 1/2” conduit bushing on left
Z22 = Black cover
9013FRG reverse
action, fully-adjustable
H One N.O., one N.C. contact Yes
M3 One N.O., one N.C. contact Yes
M5 Maintained manual cut-in lever (auto-on) Yes
B7 One rubber grommet, export only Yes
B8 Two rubber grommets, export only Yes
T 1/2" conduit tting per the NEC. With 1/4" long
threads – on right hand side, rear facing
Yes
Q1 Plastic ange with integral molded pressure
connection. (max. temp 120°F, max. pressure 80 PSI)
Yes
P Optional Pulsation plug* Yes
Z22 Black cover Yes
9013FRG Series of Pressure Switches
*** Use chart to interpret catalog number only.