Operator's Manual Model S60-12020 IMPORTANT This manual contains information for the safety of persons and property. Read it carefully before assembly and operation of the equipment! Spyker Spreaders Contact Us at 800.972.6130 ©2011 Spyker Spreaders/A Brinly-Hardy Co. 1008290 Rev.
3 Hopper Explosion 74 25 39 38 22 4 40 36 37 34 40 35 45 52 48 47 27 61 33 42 44 Rate Gate Explosion 53 46 28 74 71 74 49 26 27 71 30 56 55 54 21 62 63 57 1008290 Rev.
65 73 64 66 72 1 Spinner/Axle Explosion 24 9 12 6 7 8 7 17 11 16 16 15 14 5 18 19 13 20 10 32 10 10 59 31 10 74 Frame Explosion 67 59 69 74 27* 67 27* 75 68 74 70 68 70 3 29 68 77 3 2 3 29 68 3 70 2 76 *As needed for shimming 3 1008290 Rev.
No. Part Number Qty Description No.
1. Remove clips from axles on outside of axle frame assembly. Install wheel washer on each end of axle. 2. Install Wheel on each side of axle (Valve Stem Out). On the drive wheel side, install 3/16 x 1-3/4" Clevis Pin and Cotter Pin, Figure 1. On opposite side install wheel washer and Rue Ring Locking Pin on outside of wheel. NOTE: Extra wheel washers are provided and are to be used for shimming as needed. Wheels need to set snug against frame. Figure 1 Drive Wheel 3.
4. Install linkage to lever, Figure 3. Figure 3 5. Turn handle/linkage assembly sideways and insert end of linkage into rate gate linkage, Figure 4. Figure 4 6. Install handle to frame as shown using 1/4" x 1-3/4" Bolts and Locknuts. NOTE: You'll need to orient and install the cable bracket as shown on the left side of the spreader, Figure 5. Figure 5 1008290 Rev.
. Install two agitator wires on the upper spinner shaft. The larger agitator goes on the top/end of the shaft. Note orientation of agitator on page 9. 8. Install felt washer on shaft below the agitator wires. Slide shaft down through hopper. Install fan and coupler, Figure 6. Assemble so upper and lower spinner shafts interlock grooves. Slide coupler down over shafts. Figure 6 Ensure the factory installed felt washer is on the lower spinner shaft, Figure 6. UPPER SPINNER SHAFT FELT WASHER 9.
READ BEFORE USING OPERATE SAFELY Do not wear loose fitting clothing that can get caught in moving parts. Keep bystanders away when you operate this machine. Use this machine for intended purpose only. Always wear eye protection when operating the equipment. Do not let children or an untrained person operate machine. Stay alert for holes in the terrain and other hidden hazards. Keep all parts in good condition and properly installed. Fix damaged parts immediately. Replace worn or broken parts.
READ BEFORE USING Become Familiar With The Operation Of The Spreader Before You Put Material In The Hopper • Practice walking with the spreader, opening and closing the rate gate at the appropriate times. • Travel at a constant speed and operate the spreader lever position. Remember: Open the rate gate after the spreader is in motion at operating speed (about 3 mph, or at a brisk walking pace). • dial setting on the low side. If the setting proves to be too low, cover the area more than one time.
READ BEFORE USING to wonder where you are or where you have been. Continue until spreading is completed. Now You Are Ready To Put Material In The Hopper WARNING: Avoid Injury! Chemicals can be dangerous. Avoid injury to operators or bystanders. • Make sure the rate gate is in the closed position. • Read chemical container label for handling instructions. A Material Safety Data Sheet (MSDS) should be supplied by the chemical dealer and provides proper safety information.
NOTE: Dial Settings Are Approximate Only ! Product Particle Size Fine Pellets Mixed Fine Pellets Small Pellets Nitrogen Pellets Medium Size Medium Pellets And Granuals Large Heavy Pellets Lbs. per 1000 sq. ft. Dial Settings Full Rate Once Over Dial Settings Half Rate Twice Over 1 3.6 3.1 2 3 4.0 4.2 3.5 3.7 2 3.7 3.2 4 6 4.7 4.1 5.2 4.5 2 3 4 4.2 2.2 3.7 6 4.5 4 1 3.5 3 2 3 4.2 4.7 3.7 4 2 3 4 6 3.5 4.2 5.2 2 4 6 3.8 4.9 5.9 3.8 4.5 3.3 4.1 4.
1 YEAR LIMITED WARRANTY This is warranted to the original purchaser only. Spyker will replace parts with defects in materials and workmanship, for a period of one year from the date of purchase. For Spyker Spreaders–a Brinly-Hardy Company, products employing metal gear systems, pinion and bevel, these metal gears, only, not inclusive of any other parts or materials, are warranted for the life of the spreader, not to be used for replacement or repair past original purchase.
