Operator's Manual Model P30/S30 Series IMPORTANT This manual contains information for the safety of persons and property. Read it carefully before assembly and operation of the equipment! Spyker Spreaders Contact Us at 800.972.6130 ©2010 Spyker Spreaders/A Brinly-Hardy Co. 1008146 Rev.
7 Hopper Explosion 7 1 1 1 1 21 19 20 1 2 1 5 7 10 17 15 4 8 11 11 9 18 50 54 55 2 Rate Gate Explosion 12 2 22 13 14 16 53 52 1 6 60 55 44 55 7 7 55 2 51 47 55 55 56 57 2 7 45 55 55 56 2 59 46 7 39 49 43 7 59 43 58 3 39 Frame Explosion 48 2 1008146 Rev.
Spinner/Axle Explosion 42 24 40 25 23 31 29 33 27 27 30 36 26 28 37 34 24 28 32 35 38 3 1008146 Rev.
No. Part Number Qty Description No.
1. Install spinner to spinner shaft. Press down on spinner until it snaps into place on the roll pin, Figure 1. 2. Install axle/transmission assembly into frame as shown, Figure 1. IMPORTANT! Note the orientation of the axle/transmission assembly is critical. See the hole locations in Figure 1. One side has hole near the end of the axle, the other next to the frame. 3. Figure 1 Slide the axle bearings over the axle and into place in the frame, Figure 1. Hole Hole Axle Bearing Figure 2 4.
. On the other side of the axle install a wheel washer and rue ring locking pin, Figure 4. Figure 4 7. Place hopper onto frame. IMPORTANT! Note orientation of rate dial. Be sure to slide spinner shaft into hopper, Figure 5. 8. Insert 1/4" Nylon Washer onto 1/4-20 x 1-3/4" Bolt. Insert through hopper and frame. Attach finger tight only with 1/4" Nylon Insert Locknut, Figure 5. Repeat for remaining 3 bolts, washers, and nuts. Tighten fully. 9. Figure 5 Slide felt washer over spinner shaft, Figure 6.
10. Install Hitch Tow Bar onto frame, Figure 7. Attach with 1/4-20 x 1-3/4" Bolt and 1/4" Nylon Insert Locknut. Figure 7 11. Install Hitch Plates to end of Tow Bar using 1/4-20 x 1-3/4" Bolts and 1/4" Nylon Insert Locknuts, Figure 8. Install Hitch Pin and Large Cotter Pin, Figure 8. Figure 8 12. Slide Control Lever into U shaped bracket as shown, Figure 9. The label on the U shaped bracket faces the hopper. Label 13. Install Control Linkage into Control Lever.
16. Turn Control Bracket assembly sideways as shown, Figure 11. Install end of linkage into rate gate bracket. Figure 11 17. Install front of control lever assembly onto Tow Bar with 1/4-20 x 1-3/4" Bolt, 1/4" Washer (one on each side of tow bar) and 1/4" Nylon Insert Locknut, Figure 12. Do not fully tighten at this point. Figure 12 1008146 Rev.
18. Install Frame Braces to Frame using 1/4-20 x 1-3/4" Bolt, 1/4" Washer (one on each side) and 1/4" Nylon Insert Locknut, Figure 13. 19. Attach Frame Braces to Tow Tube/Control Lever Assembly using 1/4-20 x 2" Bolt, 1/4" Washers (one on each side), and 1/4" Nylon Insert Locknut. Figure 13 20. With rate gate dial set to 0, move control lever back and forth and ensure rate gate opens and closes fully, Figure 14. If necessary adjust Control Lever Bracket assembly forward or necessary.
READ BEFORE USING OPERATE SAFELY Keep bystanders away when you operate this machine. Use this machine for intended purpose only. Do not let children or an untrained person operate machine. Keep all parts in good condition and properly installed. Fix damaged parts immediately. Replace worn or broken parts. Do not modify the machine or safety devices. Unauthorized modifications to the machine may impair its function and safety, and void the warranty.
READ BEFORE USING Become Familiar With The Operation Of The Spreader Before You Put Material In The Hopper • Practice walking with the spreader, opening and closing the rate gate at the appropriate times. • Travel at a constant speed and operate the spreader lever position. Remember: Open the rate gate after the spreader is in motion at operating speed (about 3 mph, or at a brisk walking pace). • Close the rate gate while spreader is still at operational speed.
READ BEFORE USING • Wear proper clothing and safety equipment while handling or applying chemicals. • Prohibit all smoking, drinking, and eating around chemicals. • When spreading products containing herbicides, exercise extreme caution with respect to careless spreading and to wind-drift. Contact Of Some Products On Some Plants Can Be Fatal. • Fill the spreader on a flat, level surface only. Fill on sidewalk, driveway, cardboard, etc. to avoid material loss.
ACCUWAY - What It Does The Accuway Spread Pattern Equalizer Balances the spread pattern - Bulls Eye - Dead to the Center of the Spreader. All products. All spreading conditions. Skewing is eliminated. Does not change the spread width. ACCUWAY - How It Works Accuway shifts the material placement on the spreader spinner fan. This in turn, balances the pattern heavier to the right or heavier to the left.
NOTE: Dial Settings Are Approximate Only ! Product Particle Size Fine Pellets Mixed Fine Pellets Small Pellets Nitrogen Pellets Medium Size Medium Pellets And Granuals Large Heavy Pellets Lbs. per 1000 sq. ft. Dial Settings Full Rate Once Over Dial Settings Half Rate Twice Over 1 3.6 3.1 2 3 4.0 4.2 3.5 3.7 2 3.7 3.2 4 6 4.7 5.2 4.1 4.5 2 2.2 4 3 4.2 6 4.5 1 3.5 3 2 3 4.2 3.7 4.7 4 2 3.5 3 4 6 4.2 5.2 3.8 4.5 2 3.8 4.9 5.9 3.3 4.1 4.9 4 6 3.
TROUBLESHOOTING Spreader does not sit flat Deflector shut off is binding and will not open/close properly The "feet" or the flattened portion of the spreader hopper support tubes are not bent equally. Shut off plate is jammed with debris. 15 Using a hammer or pliers, bend the feet to be equal with each other. Thoroughly wash out hopper and shut off plates with water. Ensure debris is not stuck between shut off plate and rate gate plate. 1008146 Rev.
1 YEAR LIMITED WARRANTY This is warranted to the original purchaser only. Spyker will replace parts with defects in materials and workmanship, for a period of one year from the date of purchase. For Spyker Spreaders–a Brinly-Hardy Company, products employing metal gear systems, pinion and bevel, these metal gears, only, not inclusive of any other parts or materials, are warranted for the life of the spreader, not to be used for replacement or repair past original purchase.