Product Manual

English Manual Page 8 1019548-A
Assembly
2. Hitch Assembly Steps
and Mounting to UTV Steps
Insert the hitch tube (1) into the UTV receiver
and lock in place using the hitch pin (5) and the
cotter pin (14).
3. Add a 3/8"
hex nut (6) to
the 3/8" x 2-1/4
carriage bolt (9).
Slide this
bolt through
the adjustment
plate (2) using
the remaining
3/8" nut (6).
NOTE:
Move the carriage
bolt (9) up as far
as possible so it
will be out of
the way.
4. Slide the hitch tube (1) into the adjustment plate
(2) at the base, as illustrated here.
Add a 3/8" washer (13) to two 3/8 hex bolts (11).
Run these bolts through the adjustment plate (2)
and the hitch tube (1). Secure with another 3/8"
washer (13) and 3/8" nylon lock nut (7). Tighten the
bolts down.
5. Insert the six plastic square plugs (4) into the
openings of the spreader mount (3).
1. Identifying Hardware
For reassurance, lay the nuts, bolts and washers
down on page 5 to verify you’re using the correct
parts during assembly.
English Manual Page 5 1019548-A
Hardware Identifier
DO NOT RETURN PRODUCT IF YOU ARE MISSING PARTS. PLE ASE CALL: 1 [phone]
ILLUSTRATIONS ON THIS PAGE ARE TO SCALE FOR FASTER
IDENTIFICATION OF HARDWARE DURING ASSEMBLY.
Bolt: Hex Head
5/16 x 1” (x2) . . . . . . . .
2M1016 P
18
Washer: Flat,
5/16” (x4) . . . . . . . . . . . . . .
45 M 1111P
20
22
Nut: Nylon Lock
5/16" -18 (x2) . . . . . . . . . . . . .
B- 4786
Bolt: Carriage, 3/8 x 2-1/4” (x1) . . . . . . . . . . . . . . . . . . . . . . . .
11M1 23 6 P
9
Bolt: Hex Head, 3/8 x 3-1/2” (x4) . . . . . .
2M1256P
11
Bolt: Hex Head
1/4 x 1” (x4) . . . . . . . . .
2M 0 816 P
17
Washer; SAE Flat
1/4” (x8) . . . . . . . . . . . . . . . .
45M0909P
19
21
Nut: Lock, 1/4" -20 (x4) . . . . .
B-16 73P
Bolt: Hex Head, 1/2” x 3” (x4) . . . . . . . . . . . . .
2M1648P
10
Nut: Reg Hex,
3/8” -16 (x2) . . . . . . . . . . . . . .
30M1200P
6
Nut: Nylon Lock,
3/8” -16 (x4) . . . . . . . . . . . . . .
B- 4820
7
Nut: Nylon Lock
1/2” (x4) . . . . . . . . . . . . . . .
B- 50 96Y
8
ADDITIONAL HARDWARE ( Only needed for the Lesco Hitch )
Hairpin Cotter (x1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
D- 146 P
14
* Exterior circumference of washers can vary. These dimensions
are a measurement of the internal diameter of the washer.
Washer:
Flat, 1/2” (x8)
45 M1717P
12
Washer: SAE
Flat, 3/8” (x8)
45 M1313 P
13
English Manual Page 5 1019548-A
Hardware Identifier
DO NOT RETURN PRODUCT IF YOU ARE MISSING PARTS. PLE ASE CALL: 1 [phone]
ILLUSTRATIONS ON THIS PAGE ARE TO SCALE FOR FASTER
IDENTIFICATION OF HARDWARE DURING ASSEMBLY.
Bolt: Hex Head
5/16 x 1” (x2) . . . . . . . .
2M1016 P
18
Washer: Flat,
5/16” (x4) . . . . . . . . . . . . . .
45 M 1111P
20
22
Nut: Nylon Lock
5/16" -18 (x2) . . . . . . . . . . . . .
B- 4786
Bolt: Carriage, 3/8 x 2-1/4” (x1) . . . . . . . . . . . . . . . . . . . . . . . .
11M1 23 6 P
9
Bolt: Hex Head, 3/8 x 3-1/2” (x4) . . . . . .
2M1256P
11
Bolt: Hex Head
1/4 x 1” (x4) . . . . . . . . .
2M 0 816 P
17
Washer; SAE Flat
1/4” (x8) . . . . . . . . . . . . . . . .
45M0909P
19
21
Nut: Lock, 1/4" -20 (x4) . . . . .
B-16 73P
Bolt: Hex Head, 1/2” x 3” (x4) . . . . . . . . . . . . .
2M1648P
10
Nut: Reg Hex,
3/8” -16 (x2) . . . . . . . . . . . . . .
30M1200P
6
Nut: Nylon Lock,
3/8” -16 (x4) . . . . . . . . . . . . . .
B- 4820
7
Nut: Nylon Lock
1/2” (x4) . . . . . . . . . . . . . . .
B- 50 96Y
8
ADDITIONAL HARDWARE ( Only needed for the Lesco Hitch )
Hairpin Cotter (x1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
D- 146 P
14
* Exterior circumference of washers can vary. These dimensions
are a measurement of the internal diameter of the washer.
Washer:
Flat, 1/2” (x8)
45 M1717P
12
Washer: SAE
Flat, 3/8” (x8)
45 M1313 P
13
Fig. 1
6
6
9
2
Fig. 2
13
13
13
7
13
2
11
1
Side View
after Assembly
Fig. 3
3
4
4
4
4
4
4
4