USERS MANUAL
TABLE OF CONTENTS IMPORTANT SAFETY GUIDELINES 1 OPERATION GUIDE / START UP 2 CO2 / COMPRESSED AIR TANK 3-4 ELECTRONICS & SETTINGS 5-6 BATTERY CHARGING 7-8 VELOCITY ADJUSTMENT 9 SHOULDER STOCK INSTALLATION 10 DISASSEMBLE / REASSEMBLE & CLEANING INTERNALS 11-12 T-COCKING REMOVAL 13 TRIGGER ADJUSTMENT 14 ANTI CHOP EYES 15-16 CUP SEAL REMOVAL 17-18 MR3 SCHEMATICS 19 MR3 PARTS LIST 20 WARRANT
IMPORTANT SAFETY GUIDELINES !CAUTION! • • • • • • • • • • • • • 1 This paintball marker is NOT a toy; It can cause serious injury or death. Kingman recommends that customers be at least 18 years of age to purchase this product. Read this manual and air system warnings before using this product. Any modifications or tampering of original factory parts will void all warranties and liabilities from Kingman. Kingman recommends using a barrel plug or barrel sock when marker is not in operation.
OPERATION GUIDE / START UP WARNING: Always keep the marker powered off or on SAFE until you are ready to shoot. 1. To install and charge the battery see pages 6 and 8. 2. To turn the power ON, slide the Selector Switch located on the rear of the trigger frame UP to SEMI w/ EYES, SEMI, or AUTO mode. CAUTION: With the power ON, the marker is now ready to shoot. 3. Cock the marker by pulling the Snap T-Cocking Handle (#266) rearward until it latches.
CO2 / COMPRESSED AIR TANK ! DA N G E R 3 The CO2 or Compressed Air Tank can fly off with enough force to cause serious injury or death if the Valve unscrews from the cylinder head. LOOK at the Valve when removing the cylinder from the marker. Be sure that the valve is turning with the cylinder rather than remaining stationary with the marker. STOP if the Valve starts to unscrew from the cylinder. If in doubt, screw the cylinder back onto the marker and contact a trained person for repair.
INSTALLING A CO2 / COMPRESSED AIR TANK Firmly, attach the CO2 / Compressed Air Tank clockwise to the markers Dovetail Bottom Line ASA (#261). HELPFUL TIP: Make sure when installing a tank, to have the CO2 / Commpressed Air Tank filled. Make sure the CO2 / Compressed Air Tank has a bottle o-ring on the top of the valve to prevent air leaks. REMOVING A CO2 / COMPRESSED AIR TANK Firmly, unscrew the CO2 / Compressed Air Tank by turning counter-clockwise.
ELECTRONICS & SETTINGS #E24A CHARGING PORT #270 #JE101S AUTO SEMI SEMI/EYES OFF #JE30B LED LIGHT #294 ELECTRONIC GRIP TROUBLESHOOTING • • • • 5 Check to make sure there is enough air pressure to fire the marker. Battery may need to be recharged. If the Trigger is not functioning, turn the Trigger Screw (#298) clockwise to shorten the gap between the Touch Switch (#272) using an allen wrench. NOTE: Do not over extend the Trigger Screw (#298) for this can cause the Touch Switch (#272) to stick.
INSTALLING A BATTERY STEP 1 Remove the 3 M4x8 screws (#294) and left side grip panel (#270). STEP 2 Attach the Spyder battery (#JE1015) to the Battery Harness (#E24A). STEP 3 Retighten the 3 M4x8 screws (#294). HELPFUL TIP: Please note how the parts are removed for easy reassembly. REMOVING THE TOURNAMENT LOCK SWITCH STEP 1 Remove the 3 M4x8 screws (#294) and left side grip panel (#270). STEP 2 Remove the Tournament Lock Switch (#JE30B) located to the right of the Spyder Battery.
BATTERY CHARGING #JE1024 or #JE1025 LED LIGHT 7
CHARGING INSTRUCTIONS To charge a Spyder 9.6 NiMH Battery the circuit board must be in the OFF Position. Spyder Batteries (#JE1015) are not fully charged when purchased. Using the supplied Spyder Charger (#JE1024) place the charger in the charging port which is located at the rear of the trigger frame. Kingman recommends a charging time of 6-8 hours for a complete charge. IMPORTANT: You should never charge the battery over 24 hours or you can run the risk of damaging the battery or electronics.
VELOCITY ADJUSTMENT Decrease Velocity Increase Velocity #296 #260 VELOCITY ADJUSTMENT INCREASE/DECREASE To increase your velocity FPS (Feet per second) using the allen wrench turn the Velocity Adjuster (#296) clockwise. To decrease your velocity FPS (Feet per second) using the allen wrench turn the Velocity Adjuster (#296) counterclockwise. NOTE: Velocity Adjuster w/Spring Guide (#296) doesn’t remove from the rear of the Striker Plug (#260).
SHOULDER STOCK INSTALLATION #325 I>EKB:;H IJE9A #332 #16 SHOULDER STOCK INSTALLATION Place the Shoulder Stock (#332) on the back end upper section of the Receiver (#325). Once the Shoulder Stock is in place tighten the Set Screw (#16) to secure the stock to the body of the marker. The Set Screw (#16) is located on the right side of the receiver.
DISASSEMBLE / REASSEMBLE & CLEANING INTERNALS #26A #326 #260 #25 #JE18A #19A #262 TROUBLESHOOTING ONE OR MORE OF THE FOLLOWING MAY CAUSE RECOCKING RELATED PROBLEMS: • The pressure in the tank is too low. In some cases, the weather can affect the liquid in the tank and not cause it not to expand into carbon dioxide gas. • Marker needs lubrication. • Venturi Bolt (#326) needs to be cleaned. • The Striker O-ring (#19A) is damaged. Replace with new Kingman or Kingman-approved O-ring.
DISASSEMBLE REAR INTERNALS STEP 1 Remove Quick Disconnect Pin (#262). NOTE: Place a finger over the Striker Plug (#260) before removing the Quick Disconnect Pin (#262) STEP 2 Remove the Striker Plug (#262) Main Spring (#25) Striker Buffer (#26A). STEP 3 Remove the following items at the same time. Striker Bolt (#JE18A) and the Delrin Venturi Blot (#326). HELPFUL TIP: Please note how the parts are removed for easy reassembly.
T-COCKING REMOVAL #334 #269 #266 #268 #267 T-COCKING REMOVAL STEP 1 Remove Flat M4 x 8 Screw (#334). STEP 2 Slide the Snap Rail Cover (#269) toward the rear of the marker. STEP 3 Remove Snap T-Knob (#266). STEP 4 Remove the Snap T-Clip (#267). NOTE: Be careful while removing the Snap T-Springs (#268) as the tension may cause them to fly off. HELPFUL TIP: Please note how the parts are removed for easy reassembly.
TRIGGER ADJUSTMENT #272 #298 #273 TRIGGER ADJUSTMENT Adjusting the Top Trigger Set Screw (#298) clockwise will swing the Trigger (#273) closer the Touch Switch (#272) which will lessen the trigger gap. NOTE: Adjusting the Trigger Set Screw (#298) counter-clockwise will increase the trigger gap. Adjusting the lower Trigger Set Screw (#298) clockwise will shorten the Trigger (#273) stroke to the Touch Switch (#272) this will increase Trigger (#273) sensitivity.
ANTI CHOP EYES #321 #294 #03 #329 #294 15 #243
ANTI CHOP EYES The Anti Chop Eyes help prevent chopping paint by not allowing the marker to fire until a paintball is in front of the Venturi Bolt. The Eyes transmit a beam across the inside of the breech. The Circuit Board is preset from the factory and does not need to be adjusted or altered. If the Eyes are ON and do not see each other when firing your marker, you will have to clean the Eyes.
CUP SEAL REMOVAL #12 #16 STEP 3 STEP 4 #327 #16 #16 STEP 2 STEP 1 COLLAR #254 STEP 5 #290 #322 17
STEP BY STEP CUP SEAL ACCESS The following steps will provide easy accessto the Cup Seal (#12). The sign of a worn out Cup Seal (#12) is the presence of CO2/Compressed Air leaking down the barrel. STEP 1 Loosen the Disconnect Hose (#290) from the collar. STEP 2 Loosen the 2 set screws M5x12 (#16). STEP 3 Remove the Fore Grip Handle (#327). STEP 4 Loosen the 2 set screws M5x12 (#16). STEP 5 Remove the Shroud (#322).
19 323 324 322 01 320 327 325 321 329 37B 2608S 334 2608S 328 243 JE18C 262 326 16 331 332 333 MR3 SCHEMATICS
MR3 PARTS LIST 01 03 09 10C 11 12 13 14 14A 15 16 19A 20 25 26A 37B 37C 49 49B 49C 243 252 253 254 257 258 260 261 262 266 267 268 269 270 272 273 * 276 283 290 294 296 297 298 Barrel Plug Ball Stopper O-Ring #015 80D Valve Spring Cup Seal Guide Cup Seal Valve Pin Valve Body Valve Body Roll Pin Valve Body Screw M5 x 12 Screw w/ washer Striker O-Ring Barrel O-Ring Striker Spring Striker Buffer Filter O-Ring Air Filter Trigger Pin Sear Roll Pin (Small) Touch Switch Roll Pins MR3 Wire Harness MR3 Vertical / C
WARRANTY STATEMENT Kingman warrants the original retail purchaser that this product is free from defects in material and workmanship under normal use and service for a period of (1) year from the original date of purchase. Any Electronic Components in an Electronic Spyder marker are warranted for (6) months from the original date of purchase. Kingman agrees to repair or replace (at its discretion) any product within (a reasonable period of time). This warranty does not cover o-rings, cup seals, 9.
WARRANTY REGISTRATION PLEASE COMPLETE AND RETURN THIS FORM, ALONG WITH A COPY OF YOUR PURCHASE RECEIPT, WITHIN 15 DAYS OF PURCHASE SO THAT WE MAY VALIDATE YOUR 12 MONTH LIMITED WARRANTY.
