Manual

NO. VIC TOR
Name    Telephone ( )
Address
City State Zip Country
Your age E-mail address  Occupation
Product name and model
What other brand(s) of markers do you own?
Why did you purchase this Kingman marker?
Avg # of times you play paintball per month
Have you purchased products from the Internet within the last 6 months?
Comments/Suggestions:   
What is the next paintball product you intend to buy?
What are your hobbies (other than paintball)?
What are some magazines you like to read?
Item # Name of Parts
24A Sight Rail Screw
25 Striker spring
26A Striker buffer
27 Striker spring guide
27A Flat disc
23FA Striker plug (silver)
29 Velocity Adjust Screw
2431B Deluxe Trigger Frame (blue)
2431G Deluxe Trigger Frame (green)
31B Sear
33C Grip Cover Screw
2435G C/A adapter (green)
2435B C/A adapter (blue)
33F Nut Screw
36D Screw 5/32" x 5/8" w/ washer (black)
36E Screw 5/32" x 7/8" w/ washer (black)
37 Disconnect Hose
37A Filter O-ring
37B Filter
37C #011 O-ring
37D Plastic Washer
38 Safety button
42 Male to Male Adapter
2447G Sight Rail (green)
2447B Sight Rail (blue)
2441 Spare Parts Kit
5814 Double Trigger
48 Trigger Roll Pin
49 Sear Roll Pin
49A  Secondary Sear Roll Pin 
1
1002F
2408
42
9
10A
11
12
20
4GA
5A
2308G
2308B
5C
2406B
2406G
2447G
2447B
24A
23C
9 9
17K
22B
21
25
26A
27
27A
29
23FA
19A
18B
23B
16A
16A
5814
2431B
2431G
33F
2435G
2435B
36E
37A
37B
37C
37
33C
32EG
32EB
33C
37
7
15
33F
31W
38
5C
9 9
13
14
V IC T O R SEMI-AUTO
Item #  Name of Parts
1 Barrel Plug
1002F 9" Barrel (silver)
04GA Detent Cover w/ ball bearing & Spring (black)
2308G Direct Feed (green)
2308B Direct Feed (blue)
5A M4 X 6 Screw (black)
05C Direct Feed Screw (silver)
7 M5 X 14 Screw w/ washer
2406B Victor Receiver (blue)
Item #  Name of Parts
2406G Victor Receiver (green)
2408 Victor Reservoir Plug (silver)
9 O-ring #015 80D
10A Valve spring
11 Cup seal guide
12 Cup seal
13 Valve pin
14 Valve body
15 Valve body screw
Item #  Name of Parts
16A M5 x 12.5 Screw
17K Venturi bolt
18A Striker
19A Striker o-ring
20 Barrel o-ring
21 Bolt pin
22B Bolt screw
23B Quick Disconnect Pin
23C Disconnect Lock Pin
SPYDER VICTOR
14010 Live Oak Avenue, Baldwin Park, CA 91706
Telephone: [phone] Fax: [phone]
Website: www.Kingman.com
WARRANTY STATEMENT
Kingman warranties to the original customer purchaser that this product is free from defects in
material and workmanship under normal use and service for a period of 12 months from the
original date of purchase by the initial owner/purchaser. For warranty to be effective, customer
must return the enclosed warranty registration card, along with a copy of the purchase receipt,
within fifteen days of purchase. Kingman agrees to repair or replace (at its discretion) any product
within a reasonable period of time. This warranty does not cover o-rings, 9.6v rechargeable
battery, charger, scratches, nicks, normal wear and tear of parts, any modifications or normal
fading of anodizing or damage caused by dropping or hitting of products. This warranty shall not
apply if it is shown by Kingman that the consumer caused the defect or malfunction because of
misuse. This warranty only covers original factory parts. Any modifications or tampering of original
factory parts will not be covered by this warranty. Any damage caused by water will not be
covered by this warranty. Warranty work can only be conducted by Kingman technician or
Kingman authorized technicians. If product needs repair, package it carefully and send together
with your name, address, phone number and a brief description of the malfunction to:
CAUTION
• This paintball marker is NOT a toy. It can cause serious injury
or death.
• Recommend at least 18 years of age to purchase this product.
• Install a barrel plug in the barrel when not actually playing.
• All persons using this product, or within range while this product is
being used, must wear eye and face protection specifically designed for
paintball.
• Never shoot a person who is not wearing proper protection.
• Treat every paintball marker as if it were loaded.
• Never look down the barrel of the marker.
• Keep the paintball marker on safe until ready to shoot.
• Always remove gas source before disassembly.
• Fire only 0.68 caliber paintballs from this product.
• Read this manual and air system warning before using this product.
• Transfer this instruction manual upon change of marker ownership.
IMPORTANT
• Firing velocity may vary according to altitude and climate conditions.
• BEFORE using your marker in play, you must always first perform a “SAFE VELOCITY TEST”. This can only be accomplished
by using a testing device called a “Velocity Chronograph” and can be performed by the dealership where you purchased this
product or at a local paintball playing field.
• Note: This product is intended to be used at a velocity no greater than 300 feet per second (FPS).
• Recommended velocity is 280 FPS or less.
• This product is NOT intended to be used at any distance less than 25 feet.
• This paintball marker may have excess gas after removal of the tank. Please remove all paintballs and discharge the remaining
gas safely.
SPYDER VICTOR OPERATION GUIDE:
1. To put the marker on “SAFE”, push the safety from the “PUSH SAFE” side of the trigger frame.
To disengage the safety, point the marker in safe direction, push in the safety from
the “PUSH FIRE” side of the trigger frame.
2. Cock the marker by pulling the Cocking Bolt (#17K) rearward until it latches.
Caution: if you let go before it latches, your marker may fire.
3. Tighten the air tank until it is snug. If a leak occurs between the air tank and the C/A Adapter, replace the tank o-ring.
4. Install a 7/8” elbow with loader into the vertical feed. Fill the loader with .68 caliber paintballs only.
5. With the safety off, fire the marker by pulling the trigger.
6. Only use lubrication specifically designed for paintball markers. To lubricate your marker, you will need to disassemble your marker (please note how parts
are removed from marker as this will ease reassembly). Remove the Disconnect Lock Pin (#23C) and the Disconnect Pin (#23B). Hold down the Striker
Plug (#23FA) and Thumb Adjuster (#17K), as internal parts may be spring-loaded. As you pull the cocking knob out of the receiver, the Cocking Bolt (#29)
and Striker (#18B) will also be removed.
7. Lubricate o-rings #9 and #19A with a few drops of paintball oil only.
8. Reassemble parts back into the marker. Note: when putting the C ocking Bolt and S triker bac k into the marker, you will need to apply
pres sure behind the bolt while pulling the trigger at the same time. This will allow the B olt and S triker to be properly installed bac k into
the receiver.
9. When you are finished shooting the marker, first, unload the marker of all paintballs. Note: there may be a ball in the rec eiver; take a couple of
shots in a s afe direction to make s ure that the barrel and receiver are empty. S ec ond, put the barrel plug into the barrel. Put the s afety
on and slowly uns crew the air s ource tank. Caution: do not unscrew the tank valve from the tank. Doing so may cause serious injury or death.
10. Empty the hopper or remove the hopper off the marker to stop the flow of paintballs in the marker.
CO2/HP AIR TANK WARNING
WARNING
• VALVES MUST BE INSTALLED OR REMOVED ONLY BY QUALIFIED
PERSONNEL.
• BOTTLE MUST BE RETESTED SEE CO2/HP TANK LABEL FOR
RETEST DATE!
• Improper use, filling, storage or disposal of this cylinder may result in
death, personal injury and property damage.
• This cylinder must be filled only by properly Trained personnel in
accordance with CGA Pamphlets P.1 and G-6.3 available from the
Compressed Gas Association WWW.CGANET.COM
• Do not over pressurize. Do not expose pressurized cylinder to
temperatures in excess of 130 degrees F.
• Do not expose cylinder to corrosive materials and do not clean with
caustic cleaners.
• Do not alter this cylinder in any way.
• Cylinders heated to a temperature of 250 degrees F or more must be
condemned or requalified in accordance with test defined in CFR-49.
• Keep cylinder out of reach of children.
• The valve should NEVER be detached from the canister. Should this
occur, please seek assistance from a trained airsmith immediately.
• This tank is intended for paintball use only.
KINGMAN Warranty Registration
PLEASE COMPLETE AND RETURN THIS FORM, ALONG WITH A COPY OF YOUR PURCHASE
RECEIPT, WITHIN 15 DAYS OF PURCHASE SO THAT WE MAY VALIDATE YOUR ONE YEAR
LIMITED WARRANTY.
Mail to: Kingman Group
 14010 Live Oak Avenue
 Baldwin Park, CA 91706 U.S.A.
TROUBLESHOOTING
ONE OR MORE OF THE FOLLOWING MAY CAUSE RECOCKING RELATED PROBLEMS:
a. The pressure in the tank is too low or too high.
b. Need lubrication. (S ee O PE R ATIO N G UIDE in P4)
c. #19A (striker o-ring) is damaged. Replace with new Kingman or Kingman-approved o-ring.
(Note: the #19A O-ring cannot be s ubstituted by a tank o-ring or a #9 o-ring).
d. Need to clean barrel and upper chamber or the receiver.
e. Paintball may be defective (i.e. expired, change shape)
f. #9 (bolt o-ring) is damaged or the o-ring has expanded or swelled. Replace with a
new o-ring.
g. After ball breaks, remove all parts from UPPER chamber of receiver, wipe parts clean, and
reassemble parts into receiver. Also make sure to clean barrel with squeegee
HELPFUL HINTS
• Always remove air tank before any disassembly of your marker. DO NOT remove #14
(valve body) unless specific valve body repairs are needed. If needed, remove valve body
with a long, soft-tipped object such as the eraser end of a pencil. DO NOT remove the valve
body with a screwdriver as it will damage the valve body and cause air leaks. (Note: #15
sc rew must be removed prior to taking out the valve body).
• Air leaks are usually cause by a damaged valve body or damaged cup seal (#12). Replace
with new valve body and/or cup seal if necessary.
• To assure marker is assembled properly, follow the schematic drawing or place parts in
order during disassembly. Parts assembled backwards or placed in the wrong order will
cause marker to malfunction.
31B
48
49
49A