User's Manual

ManualsBrandsSpot ManualsAsset TrackersSatellite Asset Tracker

Table Of Contents

SmartOne C Basics
- Overview
- Modes of Operation
- Standard Messaging
- Reduced Messaging
- Theft Alert
- Inputs
- Serial Commands
- Satellite Communications
- Globalstar Satellite Network
Getting Started
- The SmartOne Device
- Turning On and Off
- Mounting
- Programming Overview
- Inputs
- Installation of Configuration Software
- Installation of Windows USB Driver
- Connecting Devices
SmartOne Configuration Software Overview
- User Data Entry Pane
- Status Pane
- Electronic Serial Number (ESN) Status Display Table
- List ESN(s) Button
- View Summary Button
- PROGRAM Button
- Menu Bar
- File Menu
- Tools Menu
- Help Menu
User Data Entry Pane
- Getting Started Tab
- Standard Messaging
- Standard Messaging Mode - With Motion
- SmartOne Solar Only – Speed and Heading
- Reduced Messaging Mode
- Theft Alert Mode
Standard Messaging - Without Motion
- Location Messages Tab
- Time(s) of Day Messaging
- Input Settings Tabs
- Type of Input
- Options Tab
Standard Messaging Mode - With Motion
- Motion Settings Tab
- Location Messages Tab
- Time(s) of Day Messaging
- Input Setting Tabs
- Status Changed Message
- Undesired State Message
- Accumulate/Count Message
- Type of Input
- Options Tab
Reduced Messaging Mode
- Change Location Tab
- Input Settings Tabs
- Status Changed Message
- Undesired State Message
- Accumulate/Count Message
- Type of Input
- Options Tab
Theft Alert Mode
- Change Location Tab
- Input Settings Tab
- Status Changed Message
- Undesired State Message
- Accumulate/Count Message
- Type of Input
- Options Tab
Continuous GPS Mode
- Change Location Tab
- Enabling Continuous GPS Mode
Messages
- Global Message Type
- Type 0 Message Class
- Location Message
- Device Turned On Message
- Change of Location Area Alert Message
- Input Status Changed Message
- Undesired Input State Message
- Re-Center Message
Type 1 Message Class
- Truncated Message Type – Single Packet
- Truncated Message Type – Multiple Packet Version
Type 2 Message Class
- Raw Message Type – Single Packet Version
- Raw Message Type – Multiple Packet Version
- Type 3 Message Class
- Diagnostic Message
- Replace Battery Message
- Contact Service Provider Message
- Accumulate/Count Message
Messaging Priority
- Prioritization of Periodic Standard Message Report Rates
- Message Priorities
Serial Commands
- Serial Packet Format (commands and responses)
- Serial Packet Fields
- CRC Algorithm
- Serial Packet Types
- Send Truncated Message (serial message type 0x26)
- Send Raw Message (serial message type 0x27)
- The Handshake Line
Connecting Serial Devices to the SmartOne
Appendix A - Glossary of Terms
Appendix B - Technical Support
Appendix C - RF Radiation Exposure Statement
Appendix D - Regulatory Notices
- FCC/IC Notices
- CAN ICES-3(A)/NMB-3(A)
- Avis de la FCC/IC
- CAN ICES-3(A)/NMB-3(A)1
- CE Notices
Appendix E – General Warnings
Appendix F – Specifications & Standards
Appendix G – Latitude/Longitude Decoding
Appendix H – Standard Message Decoding
Appendix I - Diagnostic Message Decoding
Appendix J - Accumulate/Count Message Decoding
Appendix K - External Input Cables
Appendix L – Battery Life Estimate

Page 40SmartOne C User Manual Conﬁdential & Proprietary Information

9100-0410-01 R2.4

UNDESIRED STATE MESSAGE

• Input 1/Input 2 - The SmartOne can be conﬁgured to send messages throughout the time the input is in the

undesired state, either to the Open or Closed position. The message interval while the input is active can be

conﬁgured in Days, Hours, and Minutes. Once the input is disabled, the SmartOne will return to the message

interval or time (s) of day for Location Messages.

• Vibration - If Vibration is Enabled, the SmartOne can be conﬁgured to send a Status Changed Message once

the device enters a state of vibration, lacks a state of vibration, or both. The message interval, while selected

undesired state is active, can be conﬁgured in Days, Hours, and Minutes.

ACCUMULATE/COUNT MESSAGE

• Input 1/Input 2 - The SmartOne can accumulate

hours and/or count events while input 1 or

input 2 is enabled. The SmartOne can send an

accumulate/count message once the conﬁgurable

intervals are speciﬁed in days, hours, and

minutes.

• Vibration - If Vibration is Enabled, the

SmartOne can accumulate hours once the

device enters a state of vibration or lacks a

state of vibration. The SmartOne can send an

accumulate message once the conﬁgurable

intervals are speciﬁed in days, hours, and

minutes.

NOTE: SOV = State Of Vibration; SOLV = State Of Leaving Vibration