Instructions for use WASHING MACHINE EN FR Contents Washer safety 2 English, 1 Français, 17 Installation instructions 3-4-5 Unpacking and leveling Removing the transit screws Minimum installation spacing Connecting water inlet Drainage Connecting the drain hose Under sink method Electrical Technical information Operating instructions 6-7-8 WFL 1300XD Control panel Wash cycle table Product description Detergent dispenser drawer Bleach cycle Wash cycles Display First-time use Daily use Pausing a cycl
WASHER SAFETY Turn off water faucets when appliance is not in use to relieve pressure on hoses and valves and to minimize leakage if a break or rupture occurs. 2 Do not use replacement parts that have not been recommended by the manufacturer (e.g. parts made at home using a 3D printer). No washer can completely remove oil.
INSTALLATION INSTRUCTIONS UNPACKING AND LEVELING Unpacking 1. Remove the washer from its packaging. 2. Make sure that the washer has not been damaged during the transportation process. If it has been damaged, contact the retailer and do not proceed any further with the installation process. Dispose of/recycle all packaging materials. Leveling 1. Install the washer on a flat sturdy floor, without resting it up against walls, furniture cabinets or anything else. 2.
CONNECTING WATER INLET If the water pipes you will be connecting to are new or unused, run the water until clear to remove any debris that could clog the water valve screens or valves before connecting the machine. NOTE: Supply shut-off valves should be easily accessible. Important: Water pressure MUST range within the values indicated on the “Technical Data” chart. 1. Screw the cold water fill hose (C blue connector) onto the cold water supply until tight. 2.
ELECTRICAL • Machine Voltage/Amperage - 120V, 60 Hz, 6 Amp. • Connection - 3-prong plug with 6’ cord is provided with the machine. • Circuit/Protector - 3-wire single phase, 120V, 60 Hz, AC, on a separate 15 Amp branch circuit. WARNING Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock.
OPERATING INSTRUCTIONS GB THANK YOU FOR PURCHASING A SPLENDIDE PRODUCT. To receive more comprehensive assistance, register the appliance on www.splendide.com CONTROL PANEL 1. SUPER WASH / MUTE button 2. POST CYCLE CARE / KEY LOCK button 3. ON/OFF button 4. PREWASH button and indicator light 5. START/PAUSE button 6. EXTRA RINSE button 7. DELAY START button 8. SPIN button 9. TEMPERATURE button 10.
WASH CYCLES Follow the instructions on the symbols of the garment’s wash care label. The value indicated in the symbol is the maximum recommended temperature for washing the garment. NOTE: The machine remembers your last option selection for Temperature, Spin Speed, and Post Cycle Care, and will use it for future wash cycles until you deselect that option i.e.
PAUSING A CYCLE To pause the wash cycle, press the START/PAUSE button again. To start the wash cycle from the point at which it was interrupted, press and hold the START/PAUSE button again. OPENING THE DOOR, IF NECESSARY Shortly after a cycle starts, the symbol turns on to signal that the door cannot be opened. While a wash cycle is running, the door remains locked. To open the door while a cycle is under way, for example, to add or remove garments, press the START/PAUSE button to pause the cycle.
CLEANING & MAINTENANCE Do not use flammable fluids to clean the washing machine. Cleaning the outside of the washing machine The outer parts and rubber components of the appliance can be cleaned using a soft cloth soaked in lukewarm soapy water. Do not use solvents or abrasives. Do not use glass or general purpose cleaners, scouring powder or similar to clean the control panel - these substances might damage the surfaces.
CLEANING THE MESH FILTERS IN THE WATER INLET VALVES 1. 3. Close water tap and unscrew the inlet hose. NOTE: Never use second-hand hoses. 1 2 Attach one inlet hose to the water faucet. Screw on coupling by hand until it is seated on washer. Use pliers to tighten couplings an additional two-thirds turn. Turn on that hose's respective water supply, and check for leaks. Tighten if necessary. Repeat this step with the second inlet hose. Both inlet hoses must be connected for washer to work properly.
TRANSPORT AND HANDLING Do not lift the washing machine by holding it at the worktop. 1. 2. 3. 4. Turn off the water, and unplug the washer. Make sure that door and detergent dispenser are properly closed. Disconnect the inlet hose from the water tap, and remove the drain hose from your draining point. Empty all the water remaining in the hoses and secure the latter so that they do not get damaged during transport. Reinsert the four (4) transport bolts.
TROUBLESHOOTING Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Service, make sure that the problem cannot be easily solved using the following list. WARNING Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. Anomalies The washing machine does not switch on.
Washer takes longer time than shown on the machine’s display. Water pressure is too low. Voltage supplied to the machine is too low. Excessive foam. An unbalanced load may cause the machine to adjust multiple times before performing a spin. The display shows fault code F5E4. The door needs to be opened between every 3 consecutive cycles. Open the door and restart the cycle.
AFTER-SALES SERVICE BEFORE CALLING THE AFTER-SALES SERVICE 1. See if you can solve the problem by yourself with the help of the suggestions given in the TROUBLESHOOTING section. IF AFTER THE ABOVE CHECKS THE FAULT STILL OCCURS, GET IN TOUCH WITH THE NEAREST AFTER-SALES SERVICE To receive assistance, call our Splendide Technical Service/ Assistance Department toll-free at 1-800-356-0766 or email us at service@westlandsales.com.
RV/MARINE WINTERIZATION SPECIAL WINTERIZATION INSTRUCTIONS FOR RV/MARINE INSTALLATIONS: Optional Winterization Instructions If you’re currently pumping antifreeze through your fresh water system, you can follow these steps to winterize your washing machine: 1. With washing machine power OFF, pour ½ quart of RV-type antifreeze into washer drum; 1. With machine power OFF, advance cycle selector knob to “Lightly Soiled”; 3. Press the Power button, then press and hold START.
ONE-YEAR LIMITED WARRANTY (USA & CANADA ONLY) WHO IS COVERED BY THIS WARRANTY This limited one-year warranty (“Warranty”) is given only to the original end-use/retail purchaser (the “First Using Purchaser”) of the accompanying Splendide product(s) (the “Splendide Product”).
