User Manual

Crossover – Quickstart Crossover – Quickstart
4 5
VOLTAiR
120V DC A udio Rail
ON
LOW CUT
StereoMono
2412
PHASE
LOW MID-HI
5
0
6
0
7
0
8
5
1
0
0
1
2
0
ROLL-OFF | dB
Crossover
X-OVER
OUT
20HzOffOnOff
VU
MID-HILOW
Input
Active Crossover
0
1
8
0
L
O
W
L
E
V
E
L
|
d
B
X
-
O
V
E
R
|
H
z
5
0
6
0
7
0
8
5
1
0
0
1
2
0
X
-
O
V
E
R
|
H
z
P
H
A
S
E
|
Ø
°
-
1
0
-
9
.
5
-
8
.
5
-
6
.
7
-
5
.
2
-
4
.
2
-
3
.
2
-
2
.
3
-
1
.
5
-
0
.
5
0
1
.
0
1
.
6
2
.
5
3
.
5
4
.
5
5
.
5
6
.
7
8
.
0
9
.
5
1
0
VU
120
6
Var
-180°
Var
0°
Off
LOW OUTPUT
LOW OUTPUT
Serial
Number
Made in Germany
Crossover
~ 115V AC / ~230V AC, 50 Hz / 60 Hz, P max. 50 W
AVIS: RISQUE DE CHOC ÉLECTRIQUE • NE PAS OUVRIR
RISK OF ELEC TRIC SHOCK
DO NOT OPEN
CAUTION
RL RL RL
L
L
RLR
INPUT
INPUT
1 3
2 4
Connect to
SPL Performer
Amplifier (s)
for remote
power on/off
AMP CTL/ 12V TRIGGER
AMP CTL/ 12V TRIGGER
IN OUT OUT
MID-HI OUTPUT
MID-HI OUTPUT
LR
RCA
R
230V AC:
T 630mA
L 250 V
115V AC:
T 1.2 A
L 250 V
Fuses:
Voltage Selection:
230V AC: T 500 mA L 250 V
115V AC: T 1 A L 250 V
1. Remove Fuse Holder
2. Exchange Fuses
3. Flip Over 4. Reinstall
VU Meter
14 1813
AMP CTL Output
AMP CTL Input
11
16
If you own SPL Performer power ampliers or other ampliers using 12V trigger
inputs you can connect the AMPCTL outputs of the Crossover with mono mini
jack cables to the AMP CTL of the ampsto trigger on and standby.
Up to 4 ampliers can be triggered together.
Mono mini jack cable not included in the scope of delivery.
Power up
Turn down the volume of the connected devices.
Switch on mains switch on the back of the Crossover (On = I).
The right VU Meter is dimly lit red.
Operation
Switch the Crossover from standby into operation by setting the standby switch
to ON.
Both VU Meters now lights up brightly.
Standby
Switch the Crossover into standby by setting the standby switch to
( = Standby).
If the Crossover is connected via AMP CTL input with an SPL device supporting
AMP CTL output(s), the Crossover is triggered between standby and operation
together with the SPL device.
The Standby Switch has to be set to ON in order to control the Crossover Standby via AMP CTL.
Power down
Turn down the volume of the connected devices.
Switch o mains switch on the rear of the Crossover (O = O).
The VU Meters no longer lights up.
11
12
13
14
15
16
17
18
Standby Switch
Mains Switch
1514
13 18
EN
DE