User Manual
Crossover – Quickstart Crossover – Quickstart
2 3
LOW OUTPUT
LOW OUTPUT
Serial
Number
Made in Germany
Crossover
~ 115V AC / ~230V AC, 50 Hz / 60 Hz, P max. 50 W
AVIS: RISQUE DE CHOC ÉLECTRIQUE • NE PAS OUVRIR
RISK OF ELEC TRIC SHOCK
DO NOT OPEN
CAUTION
RL RL RL
L
L
RLR
INPUT
INPUT
1 3
2 4
Connect to
SPL Performer
Amplifier (s)
for remote
power on/off
AMP CTL/ 12V TRIGGER
AMP CTL/ 12V TRIGGER
IN OUT OUT
MID-HI OUTPUT
MID-HI OUTPUT
LR
RCA
R
230V AC:
T 630mA
L 250 V
115V AC:
T 1.2 A
L 250 V
Fuses:
Voltage Selection:
230V AC: T 500 mA L 250 V
115V AC: T 1 A L 250 V
1. Remove Fuse Holder
2. Exchange Fuses
3. Flip Over 4. Reinstall
VOLTAiR
120V DC A udio Rail
ON
LOW CUT
StereoMono
2412
PHASE
LOW MID-HI
5
0
6
0
7
0
8
5
1
0
0
1
2
0
ROLL-OFF
| dB
Crossover
X-OVER
OUT
20HzOffOnOff
VU
MID-HILOW
Input
Active Crossover
0
1
8
0
L
O
W
L
E
V
E
L
|
d
B
X
-
O
V
E
R
|
H
z
5
0
6
0
7
0
8
5
1
0
0
1
2
0
X
-
O
V
E
R
|
H
z
P
H
A
S
E
|
Ø
°
-
1
0
-
9
.
5
-
8
.
5
-
6
.
7
-
5
.
2
-
4
.
2
-
3
.
2
-
2
.
3
-
1
.
5
-
0
.
5
0
1
.
0
1
.
6
2
.
5
3
.
5
4
.
5
5
.
5
6
.
7
8
.
0
9
.
5
1
0
VU
120
6
Var
-180°
Var
0°
Off
AMP CTL Input
10
Start up
Read the security advices on page 8!
Make sure that the selected mains voltage of the Crossover is according to the
mains voltage of your region.
Make sure that the mains switch on the rear of the Crossover is set to O
(O=O/On=I).
The standby switch on the front panel has to be set to
(standby).
Connect the supplied power cord to the Crossover and an appropriate mains
socket outlet.
If the supplied power cord does not match your mains socket outlet, please contact your dealer.
Turn o all devices you wish to connect to the Crossover.
With the RCA button on the rear you select the RCA input. If pressed, the RCA
input is active, otherwise the XLR input is used. Connect the outputs of your
preamplier to the inputs of the Crossover. Please use appropriate audio cables
(XLR, RCA).
Audio cables not included in the scope of delivery.
Connect the input of your subwoofer power amplier(s) to the LOW Output of
the Crossover.
You can connect a stereo, two mono or one mono power amplier to the Crossover. In case of a mono subwoofer
application, switch the LOW Mono/Stereo Switch to Mono – both LOW Outputs L and R feed the mono signal.
Audio cables not included in the scope of delivery.
Connect the input of your main power amplier(s) to the MID-HI Output of the
Crossover.
Audio cables not included in the scope of delivery.
If you own an SPL device supporting AMP CTL output(s) you can trigger standby
and operation. Therefore connect the AMP CTL output of the SPL device with a
mono mini jack cable to the AMP CTL input of the Crossover.
The Standby switch has to be set to ON in order to control the Crossover Standby via AMP CTL.
Mono mini jack cable not included in the scope of delivery.
You may also use other 12V trigger controller. The Crossover is in operation
mode when a switching voltage of 12 Volt DC is applied to the AMP/CTL input.
As soon as the 12 Volt DC is removed, the Crossover switches back to standby mode.
Use a mono mini jack cable where the tip is plus and the sleeve is minus.
1
2
3
4
5
6
7
8
9
10
Tip
Sleeve
XLR Audio Inputs
MID-HI Output
Standby Switch
LOW Output
Mains Voltage
Mains Switch
Mains Connector
LOW Mono/Stereo Switch
RCA Input Selector
7
9
104
8
2
3
EN
DE
5
8
7