User Manual
Table Of Contents
- 1: Introduction/Overview
- 1.1 Documentation notes
- 1.2 Important safety note
- 1.3 Product introduction
- 1.4 General product handling and operation
- 1.4.1 Protection from water and dust ingress
- 1.4.2 Powering on/off and sleep mode
- 1.4.3 Attaching, detaching, and handling modules
- 1.4.4 Attaching the strap
- 1.4.5 About the touchscreen display
- 1.4.6 Selecting the active interface
- 1.4.7 Running a function or test
- 1.4.8 Repeating a function or test
- 1.4.9 Screen title bar buttons/icons
- 1.4.10 Capturing a screen image (screenshot)
- 1.4.11 Stopping a test
- 1.4.12 Saving results
- 1.4.13 Maximum test duration for continuous tests
- 1.4.14 Interpreting results
- 1.4.15 Important MoCA module compatibility note
- 1.5 Remote control of the unit
- 1.6 Licensed feature details
- 1.7 Maintenance
- 1.8 FTP information
- 1.9 Technical support
- 2: Wi-Fi Testing Menu
- 3: 10/100/1G Testing Menu
- 4: System Menu
- 4.1 Record Manager
- 4.2 Admin Port
- 4.3 Set Date and Time
- 4.4 Sync with PC
- 4.5 Version Info
- 4.6 Battery Status
- 4.7 Download IPTV Channel Guide
- 4.8 Cal Touchscreen
- 4.9 Licensed Options
- 4.10 Update Firmware
- 4.11 System/Module Settings
- 4.11.1 System/Module Settings > Base Unit
- 4.11.2 System/Module Settings > RF Video Module
- 4.11.3 System/Module Settings > ADSL/VDSL2 Module
- 4.11.4 System/Module Settings > Combined Module Default
- 4.11.5 System/Module Settings > MoCA Module
- 4.11.6 System/Module Settings > DOCSIS Module
- 4.11.7 System/Module Settings > CSM Module
- 4.11.8 System/Module Settings > MoCA-RF Module
- 4.11.9 System/Module Settings > Wi-Fi
- 4.12 Taskforce
- 4.13 Signature Capture
- 4.14 Language Selection
- 4.15 Help and Support
- 5: IP and Video Testing
- 5.1 IP Network Setup
- 5.2 Connection Info
- 5.3 Ping
- 5.4 Traceroute
- 5.5 Web Browser
- 5.6 Packet Loss Test
- 5.7 Throughput
- 5.8 Speedtest
- 5.9 IP Video testing
- 5.9.1 Video QoS (Quality of Service)
- 5.9.2 Change Channel
- 5.9.3 Channel Guide Settings
- 6: Specifications
Tech-X Flex
®
(P5) Verizon Base Unit User Guide Rev B PRELIMINARY 3/20/2014
4-17
Intro
Wi-Fi
10/100
System
IP/Video
Specs
The following table describes the supported thresholds.
As an example, with the following setup, a Signal Strength value for a wireless B network would be
colored yellow if it were between -76 and -71 dB, and red if it were any lower:
Figure 4-8 View/Edit Thresholds screen
System/Module Settings > Wi-Fi > Download Thresholds
As an alternative to editing thresholds directly on the unit, you can download a thresholds file to set all
thresholds as a batch. This action completely overwrites all existing thresholds on the unit.
Signal Strength and Signal
Quality thresholds
Valid ranges for Signal Strength and Signal Quality results, with
independent thresholds for wireless B, G, and N networks versus
wireless AC. With these thresholds, note that:
• Theoretical minimums and maximums are applicable to these
results and therefore the corresponding values are not editable for
these thresholds.
• Marginal thresholds are calculated automatically based on pass/fail
ranges and therefore cannot be edited.
Pass Speed Test Download
Pass Speed Test Upload
Passing ranges for the Speedtest stage of the Wi-Fi Quick Test, for
both the download and upload directions, in Mbps.
Pass Packet Loss Passing ranges for the Packet Loss Test stage of the Wi-Fi Quick
Test, in percent.
Q. Test Packet Loss Duration Duration of the Packet Loss Test stage of the Wi-Fi Quick Test, in
seconds.