User Manual
Table Of Contents
- 1: Introduction/Overview
- 1.1 Documentation notes
- 1.2 Important safety note
- 1.3 Product introduction
- 1.4 General product handling and operation
- 1.4.1 Protection from water and dust ingress
- 1.4.2 Powering on/off and sleep mode
- 1.4.3 Attaching, detaching, and handling modules
- 1.4.4 Attaching the strap
- 1.4.5 About the touchscreen display
- 1.4.6 Selecting the active interface
- 1.4.7 Running a function or test
- 1.4.8 Repeating a function or test
- 1.4.9 Screen title bar buttons/icons
- 1.4.10 Capturing a screen image (screenshot)
- 1.4.11 Stopping a test
- 1.4.12 Saving results
- 1.4.13 Maximum test duration for continuous tests
- 1.4.14 Interpreting results
- 1.4.15 Important MoCA module compatibility note
- 1.5 Remote control of the unit
- 1.6 Licensed feature details
- 1.7 Maintenance
- 1.8 FTP information
- 1.9 Technical support
- 2: Wi-Fi Testing Menu
- 3: 10/100/1G Testing Menu
- 4: System Menu
- 4.1 Record Manager
- 4.2 Admin Port
- 4.3 Set Date and Time
- 4.4 Sync with PC
- 4.5 Version Info
- 4.6 Battery Status
- 4.7 Download IPTV Channel Guide
- 4.8 Cal Touchscreen
- 4.9 Licensed Options
- 4.10 Update Firmware
- 4.11 System/Module Settings
- 4.11.1 System/Module Settings > Base Unit
- 4.11.2 System/Module Settings > RF Video Module
- 4.11.3 System/Module Settings > ADSL/VDSL2 Module
- 4.11.4 System/Module Settings > Combined Module Default
- 4.11.5 System/Module Settings > MoCA Module
- 4.11.6 System/Module Settings > DOCSIS Module
- 4.11.7 System/Module Settings > CSM Module
- 4.11.8 System/Module Settings > MoCA-RF Module
- 4.11.9 System/Module Settings > Wi-Fi
- 4.12 Taskforce
- 4.13 Signature Capture
- 4.14 Language Selection
- 4.15 Help and Support
- 5: IP and Video Testing
- 5.1 IP Network Setup
- 5.2 Connection Info
- 5.3 Ping
- 5.4 Traceroute
- 5.5 Web Browser
- 5.6 Packet Loss Test
- 5.7 Throughput
- 5.8 Speedtest
- 5.9 IP Video testing
- 5.9.1 Video QoS (Quality of Service)
- 5.9.2 Change Channel
- 5.9.3 Channel Guide Settings
- 6: Specifications
Tech-X Flex
®
(P5) Verizon Base Unit User Guide Rev B PRELIMINARY 3/20/2014
3-3
Intro
Wi-Fi
10/100
System
IP/Video
Specs
Figure 3-2 Typical 10/100/1G testing diagram
3.4 IP Network Setup
(10/100/1G > IP Network Setup)
This function allows you to assign IP routing information to the unit in order to perform IP-based testing.
This function operates similarly to other interfaces; however, note that when launched from the
10/100/1G menu, the assigned IP information applies to the 10/100/1G interface/connection only.
For more information on parameters and results, see IP Network Setup on page 5-2.
Note the following:
• The unit must be connected to a suitable access device before attempting IP Network Setup (see
10/100/1G testing diagram on page 3-2).
• After a successful setup, the main menu shows an IP Network Disconnect command which will
terminate the IP connection. If an IP address was obtained via DHCP, it will be released. This
termination will happen automatically if you navigate away from the 10/100/1G menu.
3.5 Ping
(10/100/1G > Ping)
Ping, traceroute, web browsing, IPTV video testing
Provider
network/ISP
Home
router
Home
computer
Ping