User Manual
Table Of Contents
- 1: Introduction/Overview
- 1.1 Documentation notes
- 1.2 Important safety note
- 1.3 Product introduction
- 1.4 General product handling and operation
- 1.4.1 Protection from water and dust ingress
- 1.4.2 Powering on/off and sleep mode
- 1.4.3 Attaching, detaching, and handling modules
- 1.4.4 Attaching the strap
- 1.4.5 About the touchscreen display
- 1.4.6 Selecting the active interface
- 1.4.7 Running a function or test
- 1.4.8 Repeating a function or test
- 1.4.9 Screen title bar buttons/icons
- 1.4.10 Capturing a screen image (screenshot)
- 1.4.11 Stopping a test
- 1.4.12 Saving results
- 1.4.13 Maximum test duration for continuous tests
- 1.4.14 Interpreting results
- 1.4.15 Important MoCA module compatibility note
- 1.5 Remote control of the unit
- 1.6 Licensed feature details
- 1.7 Maintenance
- 1.8 FTP information
- 1.9 Technical support
- 2: Wi-Fi Testing Menu
- 3: 10/100/1G Testing Menu
- 4: System Menu
- 4.1 Record Manager
- 4.2 Admin Port
- 4.3 Set Date and Time
- 4.4 Sync with PC
- 4.5 Version Info
- 4.6 Battery Status
- 4.7 Download IPTV Channel Guide
- 4.8 Cal Touchscreen
- 4.9 Licensed Options
- 4.10 Update Firmware
- 4.11 System/Module Settings
- 4.11.1 System/Module Settings > Base Unit
- 4.11.2 System/Module Settings > RF Video Module
- 4.11.3 System/Module Settings > ADSL/VDSL2 Module
- 4.11.4 System/Module Settings > Combined Module Default
- 4.11.5 System/Module Settings > MoCA Module
- 4.11.6 System/Module Settings > DOCSIS Module
- 4.11.7 System/Module Settings > CSM Module
- 4.11.8 System/Module Settings > MoCA-RF Module
- 4.11.9 System/Module Settings > Wi-Fi
- 4.12 Taskforce
- 4.13 Signature Capture
- 4.14 Language Selection
- 4.15 Help and Support
- 5: IP and Video Testing
- 5.1 IP Network Setup
- 5.2 Connection Info
- 5.3 Ping
- 5.4 Traceroute
- 5.5 Web Browser
- 5.6 Packet Loss Test
- 5.7 Throughput
- 5.8 Speedtest
- 5.9 IP Video testing
- 5.9.1 Video QoS (Quality of Service)
- 5.9.2 Change Channel
- 5.9.3 Channel Guide Settings
- 6: Specifications
Tech-X Flex
®
(P5) Verizon Base Unit User Guide Rev B PRELIMINARY 3/20/2014
5-23
Intro
Wi-Fi
10/100
System
IP/Video
Specs
Results - Video QoS (MDI test)
Figure 5-12 Video QoS results - MDI test
Nominal Rate Payload media rate (audio and video) in kbps, used in calculating the MDI delay
factor.
Valid values are:
0 - 20000, where 0 indicates auto-detection of rate.
Parameter Description
Result Description
IP Address
Port
IP address and port of the media stream, specified at test launch.
Receive Rate Speed of frames received, in kbits/sec. For VQM testing, this is the receive rate
of the video or audio stream, as applicable. For MDI testing, this is the receive
rate of the PCR stream.
MDI
Media Loss Rate
Delay Factor (Avg)
Delay Factor (Max)
Delay Factor (Min)
See MDI measurement overview on page 5-40.
NOTE: The MDI result is colored green or red according to the fixed
pass/fail thresholds shown in the Plot tab.