User Manual
Table Of Contents
- 1: Introduction/Overview
- 1.1 Documentation notes
- 1.2 Important safety note
- 1.3 Product introduction
- 1.4 General product handling and operation
- 1.4.1 Protection from water and dust ingress
- 1.4.2 Powering on/off and sleep mode
- 1.4.3 Attaching, detaching, and handling modules
- 1.4.4 Attaching the strap
- 1.4.5 About the touchscreen display
- 1.4.6 Selecting the active interface
- 1.4.7 Running a function or test
- 1.4.8 Repeating a function or test
- 1.4.9 Screen title bar buttons/icons
- 1.4.10 Capturing a screen image (screenshot)
- 1.4.11 Stopping a test
- 1.4.12 Saving results
- 1.4.13 Maximum test duration for continuous tests
- 1.4.14 Interpreting results
- 1.4.15 Important MoCA module compatibility note
- 1.5 Remote control of the unit
- 1.6 Licensed feature details
- 1.7 Maintenance
- 1.8 FTP information
- 1.9 Technical support
- 2: Wi-Fi Testing Menu
- 3: 10/100/1G Testing Menu
- 4: System Menu
- 4.1 Record Manager
- 4.2 Admin Port
- 4.3 Set Date and Time
- 4.4 Sync with PC
- 4.5 Version Info
- 4.6 Battery Status
- 4.7 Download IPTV Channel Guide
- 4.8 Cal Touchscreen
- 4.9 Licensed Options
- 4.10 Update Firmware
- 4.11 System/Module Settings
- 4.11.1 System/Module Settings > Base Unit
- 4.11.2 System/Module Settings > RF Video Module
- 4.11.3 System/Module Settings > ADSL/VDSL2 Module
- 4.11.4 System/Module Settings > Combined Module Default
- 4.11.5 System/Module Settings > MoCA Module
- 4.11.6 System/Module Settings > DOCSIS Module
- 4.11.7 System/Module Settings > CSM Module
- 4.11.8 System/Module Settings > MoCA-RF Module
- 4.11.9 System/Module Settings > Wi-Fi
- 4.12 Taskforce
- 4.13 Signature Capture
- 4.14 Language Selection
- 4.15 Help and Support
- 5: IP and Video Testing
- 5.1 IP Network Setup
- 5.2 Connection Info
- 5.3 Ping
- 5.4 Traceroute
- 5.5 Web Browser
- 5.6 Packet Loss Test
- 5.7 Throughput
- 5.8 Speedtest
- 5.9 IP Video testing
- 5.9.1 Video QoS (Quality of Service)
- 5.9.2 Change Channel
- 5.9.3 Channel Guide Settings
- 6: Specifications
Verizon Base Unit User Guide Rev B PRELIMINARY 3/20/2014 Tech-X Flex
®
(P5)
5-18
Intro
Wi-Fi
10/100
System
IP/Video
Specs
Multicast Stream
Port
Destination IP Port
The destination UDP port associated with packets that contain the stream under
test. The unit determines which packets should be included in the audio/video
quality measurement based on the destination IP address and destination UDP
port pair. For multicast video, if you selected a channel from the channel guide,
this field is automatically populated.
As an option, you can select All Ports Open from the drop-down list which
indicates to ignore the port and use the IP address exclusively for identifying
video stream packets. In the case of unicast streams where packets are
addressed to a network device such as an STB, it can be difficult to determine
the UDP port(s) in use. Therefore, this option allows traffic analysis based on IP
address alone. While the STB may be receiving some data that is not part of the
video stream, it is likely that most traffic will be video data that qualifies for
analysis.
NOTE: For the most accurate results with the All Ports Open option, run
the test once to discover the precise port number, then restart the test
using that specific port.
In summary:
• This field indicates the logical port that the unit will monitor for video traffic, for
the specified IP address.
•The All Ports Open option is only applicable to measuring unicast streams
(for example, video-on-demand) using passive mode. The option allows the
unit to determine the destination UDP port of the packets containing the
stream under test dynamically.
Duration Duration of the test in seconds, or Continuous to run the test until manually
stopped.
Interval Interval at which to report a full set of current measurement results, applicable to
continuous tests only.
Encapsulation
Method
Encapsulation type of the stream(s) under test.
• RTP
• UDP
Parameter Description