User's Manual Part 1
Table Of Contents
- 1: Introduction
- 2: Product Overview
- 2.1 Introduction to the workflow interface
- 2.2 Product overview
- 2.3 General product handling and operation
- 2.3.1 Protection from water and dust ingress
- 2.3.2 Important battery charging note
- 2.3.3 Powering on/off
- 2.3.4 Attaching the strap
- 2.3.5 About the touchscreen display
- 2.3.6 Selecting the active interface
- 2.3.7 Running a function or test
- 2.3.8 Repeating a function or test
- 2.3.9 Screen title bar buttons/icons
- 2.3.10 Capturing a screen image (screenshot)
- 2.3.11 Stopping a test
- 2.3.12 Saving results
- 2.3.13 Maximum test duration for continuous tests
- 2.3.14 Interpreting results
- 2.4 Handling the MoCA/RF module
- 2.5 Remote control of the unit
- 2.6 Licensed feature details
- 2.7 Maintenance
- 2.8 FTP information
- 2.9 Technical support
- 3: Wi-Fi Testing Menu
- 4: 10/100/1G Testing Menu
- 5: System Menu
- 5.1 Record Manager
- 5.2 Admin Port
- 5.3 Set Date and Time
- 5.4 Version Info
- 5.5 Battery Status
- 5.6 Video
- 5.7 Cal Touchscreen
- 5.8 Licensed Options
- 5.9 Update Firmware
- 5.10 System/Module Settings
- 5.10.1 System/Module Settings > Base Unit
- 5.10.2 System/Module Settings > RF Video Module
- 5.10.3 System/Module Settings > ADSL/VDSL2 Module
- 5.10.4 System/Module Settings > Combined Module Default
- 5.10.5 System/Module Settings > MoCA Module
- 5.10.6 System/Module Settings > DOCSIS Module
- 5.10.7 System/Module Settings > CSM Module
- 5.10.8 System/Module Settings > MoCA-RF Module
- 5.10.9 System/Module Settings > Wi-Fi
- 5.11 Signature Capture
- 5.12 Language Selection
- 5.13 Help and Support
- 5.14 System Information
- 5.15 Wizard GUI
Tech-X Flex
®
(NG2) Tech-X Flex User Guide - Firmware v06.50
3-9
Intro
Overview
Wi-Fi
Ethernet
System
IP/Video
MoCA
RF
Specs
Table 3-3 Connect (Wi-Fi Setup) - Setup parameters page 3
Figure 3-5 Wi-Fi Connect parameters (Page 1)
WEP Authentication For WEP only, Type of initial authentication used by the wireless access point:
• OPEN - Effectively no authentication to associate and connect; however, all
communications following the connection will be WEP-encrypted and
therefore the unit must still have the correct key specified.
• SHARED - Requires matching keys to establish the initial connection, which
involves a more detailed handshake transaction between the devices.
Afterwards, all communications are WEP-encrypted similar to open
authentication.
NOTE: This setting does not affect how you specify the Key Type and
Key. It controls how the unit attempts initial negotiations only. Both
OPEN and SHARED WEP require a valid key.
WEP Key Slot For WEP only, the slot associated with the specified Key.
Parameter Description
DHCP After
Connect
Causes the unit to attempt a DHCP-based IP network setup if the connection is
successful. Otherwise, IP network setup will be a separate task following the
connection (see IP Testing > IP Network Setup on page 3-18).
Parameter Description
Preliminary issue - Limited distribution only!