User's Manual Part 1
Table Of Contents
- 1: Introduction
- 2: Product Overview
- 2.1 Introduction to the workflow interface
- 2.2 Product overview
- 2.3 General product handling and operation
- 2.3.1 Protection from water and dust ingress
- 2.3.2 Important battery charging note
- 2.3.3 Powering on/off
- 2.3.4 Attaching the strap
- 2.3.5 About the touchscreen display
- 2.3.6 Selecting the active interface
- 2.3.7 Running a function or test
- 2.3.8 Repeating a function or test
- 2.3.9 Screen title bar buttons/icons
- 2.3.10 Capturing a screen image (screenshot)
- 2.3.11 Stopping a test
- 2.3.12 Saving results
- 2.3.13 Maximum test duration for continuous tests
- 2.3.14 Interpreting results
- 2.4 Handling the MoCA/RF module
- 2.5 Remote control of the unit
- 2.6 Licensed feature details
- 2.7 Maintenance
- 2.8 FTP information
- 2.9 Technical support
- 3: Wi-Fi Testing Menu
- 4: 10/100/1G Testing Menu
- 5: System Menu
- 5.1 Record Manager
- 5.2 Admin Port
- 5.3 Set Date and Time
- 5.4 Version Info
- 5.5 Battery Status
- 5.6 Video
- 5.7 Cal Touchscreen
- 5.8 Licensed Options
- 5.9 Update Firmware
- 5.10 System/Module Settings
- 5.10.1 System/Module Settings > Base Unit
- 5.10.2 System/Module Settings > RF Video Module
- 5.10.3 System/Module Settings > ADSL/VDSL2 Module
- 5.10.4 System/Module Settings > Combined Module Default
- 5.10.5 System/Module Settings > MoCA Module
- 5.10.6 System/Module Settings > DOCSIS Module
- 5.10.7 System/Module Settings > CSM Module
- 5.10.8 System/Module Settings > MoCA-RF Module
- 5.10.9 System/Module Settings > Wi-Fi
- 5.11 Signature Capture
- 5.12 Language Selection
- 5.13 Help and Support
- 5.14 System Information
- 5.15 Wizard GUI
Tech-X Flex
®
(NG2) Tech-X Flex User Guide - Firmware v06.50
2-47
Intro
Overview
Wi-Fi
Ethernet
System
IP/Video
MoCA
RF
Specs
Figure 2-41 Remote control over an internet connection
This type of remote control allows access to nearly all test and management functions on the unit unless
you connect the unit over a Wi-Fi Admin Port, in which case all functions within the Wi-Fi menu (F2) will
be unavailable. To set it up:
1. At the subscriber site, if you plan to use a 10/100/1G Admin Port, connect the unit to the router with
a physical 10/100 (Ethernet) cable.
2. On the unit, set up a Wi-Fi Admin Port or a 10/100/1G Admin Port port (respectively) with
connectivity to the LAN, in a standard manner. For more information, see Admin Port on page 5-5.
3. Select System > Admin Port > WAN Remote Control > Enable WAN Remote Control. Note that
this step configures the router, in order to establish a VNC traffic path to the unit.
4. In the Enable WAN Remote Control results, make note of the following information which will be
required for the remote VNC client user:
• External IP Address - The address assigned to the WAN interface
• External VNC Port - The port that incoming VNC traffic must use
-or-
-or-
VNC
client
LAN
port
WAN
port
Internet
BHR
Wi-Fi
10/100
Admin Port
Ethernet
Wi-Fi
Admin Port
-or-
Preliminary issue - Limited distribution only!