User's Manual Part 1
Table Of Contents
- 1: Introduction
- 2: Product Overview
- 2.1 Introduction to the workflow interface
- 2.2 Product overview
- 2.3 General product handling and operation
- 2.3.1 Protection from water and dust ingress
- 2.3.2 Important battery charging note
- 2.3.3 Powering on/off
- 2.3.4 Attaching the strap
- 2.3.5 About the touchscreen display
- 2.3.6 Selecting the active interface
- 2.3.7 Running a function or test
- 2.3.8 Repeating a function or test
- 2.3.9 Screen title bar buttons/icons
- 2.3.10 Capturing a screen image (screenshot)
- 2.3.11 Stopping a test
- 2.3.12 Saving results
- 2.3.13 Maximum test duration for continuous tests
- 2.3.14 Interpreting results
- 2.4 Handling the MoCA/RF module
- 2.5 Remote control of the unit
- 2.6 Licensed feature details
- 2.7 Maintenance
- 2.8 FTP information
- 2.9 Technical support
- 3: Wi-Fi Testing Menu
- 4: 10/100/1G Testing Menu
- 5: System Menu
- 5.1 Record Manager
- 5.2 Admin Port
- 5.3 Set Date and Time
- 5.4 Version Info
- 5.5 Battery Status
- 5.6 Video
- 5.7 Cal Touchscreen
- 5.8 Licensed Options
- 5.9 Update Firmware
- 5.10 System/Module Settings
- 5.10.1 System/Module Settings > Base Unit
- 5.10.2 System/Module Settings > RF Video Module
- 5.10.3 System/Module Settings > ADSL/VDSL2 Module
- 5.10.4 System/Module Settings > Combined Module Default
- 5.10.5 System/Module Settings > MoCA Module
- 5.10.6 System/Module Settings > DOCSIS Module
- 5.10.7 System/Module Settings > CSM Module
- 5.10.8 System/Module Settings > MoCA-RF Module
- 5.10.9 System/Module Settings > Wi-Fi
- 5.11 Signature Capture
- 5.12 Language Selection
- 5.13 Help and Support
- 5.14 System Information
- 5.15 Wizard GUI
Tech-X Flex User Guide - Firmware v06.50 Tech-X Flex
®
(NG2)
2-30
Intro
Overview
Wi-Fi
Ethernet
System
IP/Video
MoCA
RF
Specs
mandate on how any given organization should interpret results. In all cases, you should consult local
and corporate protocol for the standards by which you interpret results. This document does not intend in
any way to serve as an authorized or approved standard for the operation and maintenance of any
telecommunications network.
2.4 Handling the MoCA/RF module
The following sections provide important information about attaching, detaching, and connecting the
optional MoCA/RF module. For comprehensive information on module functionality, see:
• MoCA/RF - MoCA Testing on page 7-1
• MoCA/RF - RF Testing on page 8-1
Note that the normal functionality of the base unit (Wi-Fi, 10/100/1G, etc.) remains unchanged while the
module is attached.
2.4.1 Attaching, detaching, and handling the module
CAUTION: Before attaching or detaching a module, the unit must be powered off or
placed into sleep mode. Failure to do this could result in damage to the module
or base unit firmware. For more information on initiating sleep mode, see
Powering on/off on page 2-22.
NOTE: To prevent damage to the module bay and to keep electrical connections clean, you should
keep the module placeholder (the “dummy” module) installed when no module is in use. New
units are shipped with the placeholder attached.
A modules is fastened to the base unit using fastener screws attached to the upper “feet” of the unit. To
remove a module, loosen/disengage the two screws and gently pull the module from its electrical
connection. Likewise, to attach a module, gently press the module into the base unit to seat the electrical
connection, then finger-tighten the screws.
Preliminary issue - Limited distribution only!