User's Manual Part 1
Table Of Contents
- 1: Introduction
- 2: Product Overview
- 2.1 Introduction to the workflow interface
- 2.2 Product overview
- 2.3 General product handling and operation
- 2.3.1 Protection from water and dust ingress
- 2.3.2 Important battery charging note
- 2.3.3 Powering on/off
- 2.3.4 Attaching the strap
- 2.3.5 About the touchscreen display
- 2.3.6 Selecting the active interface
- 2.3.7 Running a function or test
- 2.3.8 Repeating a function or test
- 2.3.9 Screen title bar buttons/icons
- 2.3.10 Capturing a screen image (screenshot)
- 2.3.11 Stopping a test
- 2.3.12 Saving results
- 2.3.13 Maximum test duration for continuous tests
- 2.3.14 Interpreting results
- 2.4 Handling the MoCA/RF module
- 2.5 Remote control of the unit
- 2.6 Licensed feature details
- 2.7 Maintenance
- 2.8 FTP information
- 2.9 Technical support
- 3: Wi-Fi Testing Menu
- 4: 10/100/1G Testing Menu
- 5: System Menu
- 5.1 Record Manager
- 5.2 Admin Port
- 5.3 Set Date and Time
- 5.4 Version Info
- 5.5 Battery Status
- 5.6 Video
- 5.7 Cal Touchscreen
- 5.8 Licensed Options
- 5.9 Update Firmware
- 5.10 System/Module Settings
- 5.10.1 System/Module Settings > Base Unit
- 5.10.2 System/Module Settings > RF Video Module
- 5.10.3 System/Module Settings > ADSL/VDSL2 Module
- 5.10.4 System/Module Settings > Combined Module Default
- 5.10.5 System/Module Settings > MoCA Module
- 5.10.6 System/Module Settings > DOCSIS Module
- 5.10.7 System/Module Settings > CSM Module
- 5.10.8 System/Module Settings > MoCA-RF Module
- 5.10.9 System/Module Settings > Wi-Fi
- 5.11 Signature Capture
- 5.12 Language Selection
- 5.13 Help and Support
- 5.14 System Information
- 5.15 Wizard GUI
Tech-X Flex
®
(NG2) Tech-X Flex User Guide - Firmware v06.50
2-21
Intro
Overview
Wi-Fi
Ethernet
System
IP/Video
MoCA
RF
Specs
– When connected to a 10/100 network, the LED towards the bottom of the base unit will illuminate
green and flash when there is data activity
– When connected to a 1G network, the LED towards the top of the base unit will illuminate green
and flash when there is data activity
• The USB port is used for specialized functions related to transferring files to and from the unit. This
port and related functions are described elsewhere in the product documentation as applicable.
2.2.5 Unit symbols
The following table describes symbols that may appear on the physical body of the unit.
Table 2-8 Unit symbols
2.3 General product handling and operation
This section provides basic information for general operation. For most functions and tests, the buttons,
display, and other components operate in a similar fashion. Once you become familiar with general
operation, you should be able to set up and run most functions and tests, referring to this document only
as necessary for specific technical details, contained elsewhere in this document.
Symbol Description
DC power input.
Ethernet port.
Port for special use only. Do not plug anything into this port unless
specifically instructed by Spirent. Improper use could damage the unit.
USB port.
A symbol which may appear on the unit indicating that this documentation
should be reviewed thoroughly before using the product.
Preliminary issue - Limited distribution only!