User's Manual Part 1
Table Of Contents
- 1: Introduction
- 2: Product Overview
- 2.1 Introduction to the workflow interface
- 2.2 Product overview
- 2.3 General product handling and operation
- 2.3.1 Protection from water and dust ingress
- 2.3.2 Important battery charging note
- 2.3.3 Powering on/off
- 2.3.4 Attaching the strap
- 2.3.5 About the touchscreen display
- 2.3.6 Selecting the active interface
- 2.3.7 Running a function or test
- 2.3.8 Repeating a function or test
- 2.3.9 Screen title bar buttons/icons
- 2.3.10 Capturing a screen image (screenshot)
- 2.3.11 Stopping a test
- 2.3.12 Saving results
- 2.3.13 Maximum test duration for continuous tests
- 2.3.14 Interpreting results
- 2.4 Handling the MoCA/RF module
- 2.5 Remote control of the unit
- 2.6 Licensed feature details
- 2.7 Maintenance
- 2.8 FTP information
- 2.9 Technical support
- 3: Wi-Fi Testing Menu
- 4: 10/100/1G Testing Menu
- 5: System Menu
- 5.1 Record Manager
- 5.2 Admin Port
- 5.3 Set Date and Time
- 5.4 Version Info
- 5.5 Battery Status
- 5.6 Video
- 5.7 Cal Touchscreen
- 5.8 Licensed Options
- 5.9 Update Firmware
- 5.10 System/Module Settings
- 5.10.1 System/Module Settings > Base Unit
- 5.10.2 System/Module Settings > RF Video Module
- 5.10.3 System/Module Settings > ADSL/VDSL2 Module
- 5.10.4 System/Module Settings > Combined Module Default
- 5.10.5 System/Module Settings > MoCA Module
- 5.10.6 System/Module Settings > DOCSIS Module
- 5.10.7 System/Module Settings > CSM Module
- 5.10.8 System/Module Settings > MoCA-RF Module
- 5.10.9 System/Module Settings > Wi-Fi
- 5.11 Signature Capture
- 5.12 Language Selection
- 5.13 Help and Support
- 5.14 System Information
- 5.15 Wizard GUI
Tech-X Flex User Guide - Firmware v06.50 Tech-X Flex
®
(NG2)
2-14
Intro
Overview
Wi-Fi
Ethernet
System
IP/Video
MoCA
RF
Specs
VOD SCORING Establishes an IP interface using
DHCP, then runs a Video QoS test.
This workflow requires several setup
steps, including the physical initiation
of a VoD stream on the network and
the entry of several complex setup
parameters. The setup and results of
the Video QoS test use classic view
screens.
See Video QoS (Quality of Service) on
page 6-23.
CABLE TEST Initiates an Ethernet Cable Test, with
no user input required. Assuming a
connection with an active Ethernet
signal, the following conditions cause
a failed condition:
• The link status is not 1 Gbps full
duplex -or- if auto-negotiation fails.
• The link is not 1 Gbps link due to
one or more open pairs.
• Pair polarity or straight-through
mapping is incorrect.
• Any skew value is greater than 16
ns.
See Ethernet Cable Test on page 4-6.
WI-FI CLASSIC Switches to the classic 10/100/1G
menu. This action closes the workflow
view completely.
See 10/100/1G Testing Menu on page 4-1.
Workflow Description/notes For more information
Preliminary issue - Limited distribution only!