User's Manual Part 1
Table Of Contents
- 1: Introduction
- 2: Product Overview
- 2.1 Introduction to the workflow interface
- 2.2 Product overview
- 2.3 General product handling and operation
- 2.3.1 Protection from water and dust ingress
- 2.3.2 Important battery charging note
- 2.3.3 Powering on/off
- 2.3.4 Attaching the strap
- 2.3.5 About the touchscreen display
- 2.3.6 Selecting the active interface
- 2.3.7 Running a function or test
- 2.3.8 Repeating a function or test
- 2.3.9 Screen title bar buttons/icons
- 2.3.10 Capturing a screen image (screenshot)
- 2.3.11 Stopping a test
- 2.3.12 Saving results
- 2.3.13 Maximum test duration for continuous tests
- 2.3.14 Interpreting results
- 2.4 Handling the MoCA/RF module
- 2.5 Remote control of the unit
- 2.6 Licensed feature details
- 2.7 Maintenance
- 2.8 FTP information
- 2.9 Technical support
- 3: Wi-Fi Testing Menu
- 4: 10/100/1G Testing Menu
- 5: System Menu
- 5.1 Record Manager
- 5.2 Admin Port
- 5.3 Set Date and Time
- 5.4 Version Info
- 5.5 Battery Status
- 5.6 Video
- 5.7 Cal Touchscreen
- 5.8 Licensed Options
- 5.9 Update Firmware
- 5.10 System/Module Settings
- 5.10.1 System/Module Settings > Base Unit
- 5.10.2 System/Module Settings > RF Video Module
- 5.10.3 System/Module Settings > ADSL/VDSL2 Module
- 5.10.4 System/Module Settings > Combined Module Default
- 5.10.5 System/Module Settings > MoCA Module
- 5.10.6 System/Module Settings > DOCSIS Module
- 5.10.7 System/Module Settings > CSM Module
- 5.10.8 System/Module Settings > MoCA-RF Module
- 5.10.9 System/Module Settings > Wi-Fi
- 5.11 Signature Capture
- 5.12 Language Selection
- 5.13 Help and Support
- 5.14 System Information
- 5.15 Wizard GUI
Tech-X Flex User Guide - Firmware v06.50 Tech-X Flex
®
(NG2)
2-6
Intro
Overview
Wi-Fi
Ethernet
System
IP/Video
MoCA
RF
Specs
Noting that a Wi-Fi connection has yet to be established, the workflow begins the connection setup. The
first screen is a modification of the classic Wi-Fi Scan, where you can select the proper customer
network. After this screen, the workflow requests the authentication parameters, similar to the classic Wi-
Fi Connect function (see Wi-Fi Setup > Connect on page 3-7).
Figure 2-7 Wi-Fi INSTALLATION workflow - Wi-Fi scan results
Once the connection parameters are submitted, the workflow enters a state of automatic processing
where it attempts to connect to the selected network, obtain an IP address, run the speed testing, and
compare the results with the specified thresholds. At any point, if the process cannot complete, the
workflow provides a warning and begins to exit.
If the testing completes without issue, the workflow presents the results. If the data rates do not meet the
thresholds, the workflow initiates a wired Ethernet speed test to determine whether the issue is
associated with the Wi-Fi connection or the upstream WAN. At this point, if either test reveals issues, you
might decide to terminate the workflow and troubleshoot accordingly.
Figure 2-8 Wi-Fi INSTALLATION workflow - WAN speed testing results
Preliminary issue - Limited distribution only!