SpiderCloud® Radio Node - SCRN-220 Hardware Installation Guide ® Part number: DOC-SCRN-220-HW-01, Rev.
FCC Statements Caution: Any changes or modification cautions to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum 25 cm between the radiator and your body.
SpiderCloud Radio Node - SCRN-220 Hardware Installation Guide Table of Contents About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Radio Node Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents 4 SpiderCloud Wireless, Inc.
SpiderCloud Radio Node - SCRN-220 Hardware Installation Guide About this Manual This guide provides the system specifications of the SpiderCloud Wireless® Radio Node 220 (SCRN-220). It includes detailed hardware installation instructions, the boot sequence, and expected LED behavior both during the boot-up and under operating conditions. An appendix shows the radio node antenna patterns. The primary audience for this guide includes network planners, system administrators and installation personnel.
SpiderCloud Radio Node - SCRN-220 Hardware Installation Guide Figure 1 on page 6 shows the logical architecture of the SCRN-220 in the network: LAN Intranet Radio Nodes PoE+ Switch GNSS Antenna MME Firewall Core Switch IPsec DMZ Security Gateway IPsec S1-C IPsec Backhaul Services Node S1-U S1 PoE+ Switch SGW LTE Email Mobile Operator Core Web LTE Enterprise Figure 1 Radio Node Relationship to Enterprise and Mobile Operator Core Networks Radio Node Models Table 1 displays the orderable con
SpiderCloud Radio Node - SCRN-220 Hardware Installation Guide Radio Node System Isometric Top View and Bottom View The following drawings display an isometric top and bottom views of the radio node: Figure 2 Radio Node Top View Figure 3 Radio Node Bottom View SpiderCloud Wireless, Inc.
SpiderCloud Radio Node - SCRN-220 Hardware Installation Guide Antennas The radio node includes four internal Tx/Rx antennas with a peak gain of 5dBi and operates in 2x2 mode with MIMO or four optional ports with QMA coaxial connectors for external antennas.
SpiderCloud Radio Node - SCRN-220 Hardware Installation Guide Ports The radio node has one 1 Gigabit Ethernet port that supports a Category 5e (Cat 5e) or better twisted-pair cable with an RJ-45 connector. Figure 6 shows the Ethernet port. There are two LEDs on the connector: • Link: Steady green state indicates a normal Layer 2 link connection has been established. • Activity: Yellow blinking indicates data activity.
SpiderCloud Radio Node - SCRN-220 Hardware Installation Guide Input Power The radio node receives its power from a standard Power Over Ethernet (PoE+) switch (typical) or injector. The radio node is fully compliant with the IEEE 802.3at PoE+ specification. Per IEEE 802.3at, use standard Cat 5e or better twisted-pair cable with a maximum length restriction of 100 meters (328 feet) for PoE+. This restriction minimizes power loss between the PoE+ power source and the radio node.
SpiderCloud Radio Node - SCRN-220 Hardware Installation Guide The illustration below shows a generic single-port PoE+ injector. Use this injector only when a PoE+ Ethernet switch is not available. CON NEC T PoE P LUS ON OUT IN Figure 9 Typical PoE+ Injector To connect the PoE+ injector to a radio node Step 1 Attach the injector power cord to a power source. Step 2 Connect an unpowered Ethernet cable from a switch to the IN port on the injector.
SpiderCloud Radio Node - SCRN-220 Hardware Installation Guide Table 2: Radio Node Specifications (continued) Security Secure boot and secure key storage using Trusted Platform Module (TPM) functions IPsec tunneling to services node X.
SpiderCloud Radio Node - SCRN-220 Hardware Installation Guide Table 3: Radio Node Specifications (continued) 1.25-Inch Bracket Dimensions Height:1.57 cm (6.2 in.) Width: 1.3 cm (5.1 in.) Depth: 3.18 cm (1.25 in.) Weight 0.24 kg. (8.
SpiderCloud Radio Node - SCRN-220 Hardware Installation Guide Select the Radio Node Location Radio nodes can be installed in a wide range of locations including walls, ceilings, and spaces above the ceiling. Follow the installation guidelines for selecting appropriate mounting locations for the unit. When mounting a radio node vertically, align the bottom-side fins vertically for superior cooling.
SpiderCloud Radio Node - SCRN-220 Hardware Installation Guide Bracket Mounting and Cabling Guidelines Incorrectly cabling and mounting a radio node can result in crushed cables and loss of communications to the unit. Follow these guidelines in cabling the radio node and mounting it on the bracket: • Ensure that the cabling is properly routed and dressed. • Ensure that the radio node is fully inserted into the mount bracket so that it locks into place and is flush.
SpiderCloud Radio Node - SCRN-220 Hardware Installation Guide Attach the mount bracket to the radio node as shown in Figure 11: Bracket Keyholes Figure 11 Radio Node Slides into Mount Bracket Installing the Radio Node (Method 1) Use this method with the quarter-inch bracket when routing the Ethernet cable through an opening where the bracket will be mounted. To route the cable directly and mount the radio node Step 1 Cut a hole in the ceiling or wall to route the Ethernet cable through.
