User Guide

J300P-2
Flange Yokes
Snap Ring Design
7 Important: See Safety Information in General Information Section (J300P-GI)
• Part is discontinued  Part is available until supply is exhausted  Not sold separately
A B - Bolt Holes C G
Flange or Bolt Diameter Number Pilot Diameter Flange Illustration Spicer
Swing Circle D-Drilled of M-Male Face to Figure Part
Diameter Diameter
T-Tapped Holes F-Female Centerline Number
1330 SERIES (Continued) E-3.875 D-1.062 USE KIT NO. 5-213X, 5-790X, 5-812X, 5-1203X
5.360 4.251 .500-D 4 2.560F 1.618 1 5002313
5002313 was replaced by 2-2-02313
5.360 4.251 .500-D 4 2.560F 1.618 1 2-2-02313
5.875 4.750 .500-D 4 2.953F 1.730 1 2-2-03489
12 mm bolt holes equally spaced. Part has hole thru ctr.
1350 SERIES E-3.875 D-1.188 USE KIT NO. 5-178X OR 5-799X
4.500 3.750 .438-D 4 2.750M 1.281 1 3-2-809
Bolt holes are equally spaced. Part has hole thru center.
4.625 3.750 .438-D 4 2.750M 1.562 1 3-2-119
5.250 4.250 .470-T 4 2.680F 1.625 1 3-2-1699
12mm threaded holes, Metric fl ange
5.250 4.250 .500-D 4 2.000F 1.625 1 3-2-1579•
5.250 4.250 .500-D 4 2.560F 1.618 1 3-2-1879
Bolt holes are equally spaced. Part has hole thru center.
5.360 4.250 .472-T 4 2.000F 1.625 1 3-2-1619
12mm threaded holes, Metric fl ange
5.750 4.750 .500-D 4 2.953F 1.750 1 3-2-1859
Bolt holes are equally spaced. Part has hole thru center.
5.812 3.938 .489-D 4 2.161F 1.913 1 5010269•
Bolt holes are equally spaced. Part has hole thru center.
6.406 5.500 .453-D 4 3.562F 1.844 1 3-2-699•
1410 SERIES E-4.438 D-1.188 USE KIT NO. 5-160X OR 5-801X
4.234 3.750 .484-D 4 2.750M 1.688 1 3-2-1329
4.625 3.750 .438-D 4 2.750F 1.688 1 3-2-299
4.625 3.750 .438-D 4 2.750M 1.688 1 3-2-159
4.625 3.750 .438-D 4 2.750M 1.938 1 3-2-439
4.724 3.996 .394-D 8 2.954F 2.531 2 3-2-1159
Metric fl ange
4.760 3.938 .484-D 4 3.149M 1.690 3-2-1549
Bolt holes are on 36 degrees
5.094 4.750 .480-D 4 3.750M 1.750 2 3-2-1779
5.240 4.250 .500-D 4 2.000F 1.620 1 3-2-1819
Part has hole thru center
5.290 4.250 .500-D 4 2.560F 1.736 1 3-2-04617
Bolts holes are equally spaced
5.352 4.250 .512-D 4 2.680F 1.620 1 3-2-1759
Bolt holes are equally spaced. Part has hole thru center.
5.352 4.250 .472-T 4 2.680F 1.620 1 3-2-1709
12mm tapped holes/OEM only
5.750 4.750 .500-D 4 2.953F 2.000 1 3-2-1839
Bolt holes are equally spaced. Part has hole thru center.
5.750 4.750 .509-D 4 3.750M 2.000 1 3-2-1789
Bolts holes are equally spaced
5.812 4.750 .531-D 4 3.750M 2.000 1 3-2-939
5.875 4.750 .480-D 4 3.750M 2.000 1 3-2-1519•
5.875 4.750 .500-D 4 3.750M 2.000 1 3-2-429
5.875 4.750 .500-D 4 3.750M 1.750 1 3-2-549
5.875 4.750 .500-D 4 3.750M 1.500 1 3-2-559
12mm threaded holes equally spaced
6.375 5.500 .438-D 4 3.562F 1.844 1 3-2-709
6.750 5.750 .484-D 4 4.803F 2.000 3 3-2-1659-1
Bearing strap style yoke w/brake pilot and bolt pattern
6.875 6.125 .375-D 8 6.875M 2.000 2 3-2-309
Flange has pilot for brake